Crestron electronic 4 Channel Fluorescent Dimming Module CNLFDB-4 User Manual
Crestron cnlfdb-4
Controls
ID CODE: (2) Rotary DIP Switches, set Cresnet ID
NORMAL/OVERRIDE: (1) Slide switch, OVERRIDE forces all channels to full on
LED Indicators
NET POWER: Indicates DC power supplied from Cresnet network
ACTIVITY: Indicates communication with Cresnet system
Channels 1 – 4: Indicate each relay is energized
Environmental
Temperature: 32° to 104°F (0° to 40°C)
Humidity: 10% to 90% RH (non-condensing)
Heat Dissipation: 17 BTU/Hr + (0.3 BTU/Hr x Load Current in Amps) + (0.02 per ballast),
40 BTU/Hr at maximum load
Enclosure
Occupies 2 module spaces in a CLC-6 cabinet (order optional MTPL-02074-1 space plate)
Occupies 1 module space in a CSTC cabinet
Weight
3.5 lbs (1.59 kg)
www.crestron.com
|
800.237.2041
The CNLFDB-4 dimming module provides 4 channels of dimming for fluorescent
lighting fixtures equipped with Lutron
®
Hi-lume
®
or Eco-10™ three-wire electronic
fluorescent dimming ballasts. The CNLFDB-4 occupies a single module space in
any CSTC cabinet, or two spaces in a CLC-6 cabinet. The unit is designed to
communicate with the PAC2 control system, or any Crestron control system, via
the Cresnet control network.
> 4 channels of phase-controlled dimming for Lutron Hi-lume FDB
or Eco-10 ECO three-wire electronic type fluorescent ballasts
> Switch control of non-dimmable loads
> Available for 120 or 277 Volt AC
> Occupies 1 module space in a CSTC lighting cabinet
> Controlled by PAC2 or PAC2M automation control system
AVAILABLE MODELS
CNLFDB-4 4 Channel Fluorescent Dimmer, 3-Wire Electronic, 120V
CNLFDB-4/277 4 Channel Fluorescent Dimmer, 3-Wire Electronic, 277V
SPECIFICATIONS
Load Ratings
Dimmer Channels: 4
Per Channel: 16 Amps
Module Total: 64 Amps
Load Types: Hi-lume FDB or Eco-10 ECO 3-wire electronic fluorescent dimming ballasts
Load Control: Phase-controlled dimming signal plus air-gap relay
Relay Rating: 20 Amp at 277 Volts AC, 1HP at 125 Volts AC
Power Requirements
Line Power: 120 or 277 Volts AC, 60Hz, single-phase, all feeds must be same phase
Cresnet Power Usage: 4 Watts (0.17 Amp @ 24 Volts DC)
Connectors
NET: (1) 4-pin 5mm detachable terminal block, Cresnet slave port
Connects to Cresnet control network
L-IN 1 - 4: (4) Captive screw terminals, line power inputs
L-OUT 1 - 4: (4) Captive screw terminals, switch outputs
DIM 1 - 4: (4) Captive screw terminals, dimmer outputs
NEUT: (1) Captive screw terminal, neutral
Specifications subject to change without notice. Doc.4833 12/07
©2007 Crestron Electronics, Inc. All brand names, product names and trademarks are the property of their respective owners.
Crestron Electronics, Inc. 15 Volvo Drive
l
Rockleigh, NJ 07647
Tel: 800.237.2041 / 201.767.3400
l
Fax: 201.767.1903
Crestron CNLFDB-4
4 Channel Fluorescent Dimming
Module, 3-Wire Electronic