Ciprico DIMEDA 10G - Manual (Page 2)

Step 9. Configure SMTP
Simple Mail Transfer Protocol (SMTP) notifies an administrator via
e-mail when an event occurs in the DiMeda system. To disable SMTP,
leave the window blank and click on the Next icon. To enable SMTP, click
in the Enable box and do the following:
a. Enter the IP address of the mail server.
b. Remove a contact by clicking on its name and the Remove button.
c. Add, edit, or maintain the default contact by clicking on the
appropriate button. The SMTP Contact window appears.
d. Enter the name, e-mail address, event severity, and time during
which this contact will be notified. Click on OK to return to the SMTP
window. Click on Next.
Step 10. Save and Reboot
a. In the SMTP window, click on the Save icon. DiMeda asks if you are
sure you want to save this configuration.
b. Click on OK. A message appears, reporting that the setup was
successful and requesting that you reboot.
c. Click on Reboot Now. A message appears, telling you the system is
rebooting.
d. Close the browser. Do not power down the enclosure.
e. After two minutes, open a browser. In the address bar, enter the
public IP address you created in Step 4. Rebooting takes between 2
and 10 minutes. Refresh until the Welcome window appears.
f. Enter the password you created in Step 6.
Step 11. Create a File System
A welcome window appears, reminding you to create a file system. Click
on the Yes button. The File System Creation window appears.
a. Click on the device from the Available Devices List. The size of the
file system you are creating appears.
b. Choose one of these File System Types: Video application or
General Purpose application.
c. Enter the mount point.
d. Choose a method for communicating with client systems when
exchanging files between computers: NFS (Unix), CIFS (Windows),
or both. Click on Next.
Step 12. Create Shares
If you chose NFS, the NFS Share window appears. Specify NFS options.
If you chose CIFS, the CIFS Share window appears. Specify CIFS
options. If you chose AFP, the AFP Share window appears. Specify AFP
options. Click on the Save icon.
DiMeda is now attached to your network, ready to store, retrieve, and
share files between your networked clients - reliably and at high speed.
LCD Display
The liquid crystal display (LCD) panel enables you to enter commands.
Use the arrow, F1, F2, and Enter buttons to view status or enter
commands.
• To view Status, press F1.
• To view the menu, press F2.
• To select or confirm a menu option, press Enter.
Status
The LCD screen displays the following status:
• Booting
• Good
• Halted
• Monitor (when the appliance is in monitor mode)
• Warning
Actions
To shut down the array, do the following:
a. Press F2 to view the menu.
b. Use the up or down arrow to select Shutdown.
c. Press Enter. The system asks you to confirm.
d. Press Enter again.
To reboot, do the following:
a. Press F2 to view the menu.
b. Press the up or down arrow until Reboot appears.
c. Press Enter. The system asks you to confirm.
d. Press Enter again.
To change the IP address, do the following
a. Press F2 to view the menu.
b. Use the up or down arrow to select Set IP.
c. Press Enter. The system displays the current IP address.
d. Use the up and down arrows to change numbers. Use the left and
right arrows to move from digit to digit.
e. Press Enter when the new IP address is complete. If the update was
successful, the LCD displays the following:
IP address was set
F1=Status F2=Menu
f. If the update was unsuccessful, the LCD displays the following:
Error setting IP Addr.
F1=Status F2=Menu
45
08
Copyright 2005 Ciprico, Inc., All rights reserved.
Ciprico Support in the U.S. 1-877-CIPRICO (247-7426).
For questions about this product, e-mail [email protected].
Log onto the Ciprico Web site at www.ciprico.com