Clarion DVC920 - Manual (Page 4)

280-7804-00
5
DVC920
6
DVC920 DVC920
7
3. CONTROLS / LES COMMANDES / CONTROLES /
4. NOMENCLATURE
Names of Buttons
Control Unit
[VOL] button:
• Raises and lowers the volume.
• Changes the adjustment values in the ADJUST
MODE and AUDIO MODE.
[MUTE] button:
• Turns off the sound.
[DISP] button:
• Changes the display.
• Changes set items in the ADJUST MODE.
[ENT] button:
• Determines the adjustment setting in the AD
JUST MODE.
[SOURCE] button:
• Switches the input source.
[A-MODE] button:
• Adjusts the volume balance in each speaker.
[ADJUST] button:
• Invokes the ADJUST MODE to set speakers
and other equipment.
[DSF] button:
• Changes the sound characteristics in the car.
[POWER] button:
• Turns the power on and off.
Control Unit Display
D.S.F. D.S.F. indication
Title indication
DOLBY DIGITAL DOLBY Digital indicator
: Lights when playing Dolby Digital sound from the Digital input connector.
DOLBY PLII (Dolby Pro Logic II) indicator
: Lights when selecting the various Dolby Pro Logic II function modes.
LINEAR PCM LINEAR PCM indicator
: Lights when playing linear PCM sound from the Digital input connector.
DTS DTS indicator
: Lights when playing DTS sound from the Digital input connector.
Center speaker indication
Front speaker indication
Subwoofer indication
Mute indication
Rear (surround)
speaker indication
Press the [SOURCE] button on
the control unit to display image
when the input source has been
changed.
DIGITAL1:
When a digital source connected
to a digital input 1 is selected.
DIGITAL2:
When a digital source connected
to a digital input 2 is selected.
ANALOG1:
When an analog source con-
nected to an analog input with
RCA plugs is selected.
ANALOG2:
When an analog source con-
nected to an analog input with a
CeNET cable is selected.
5. OPERATIONS
Basic Operations
CAUTION
Be sure to lower the volume before switch-
ing off the unit power or the ignition key. The
unit remembers its last volume setting. If you
switch the power off with the volume up, when
you switch the power back on, the sudden
loud volume may hurt your hearing and dam-
age the unit.
Turning on/off the power
Note:
• Be careful about using this unit for a long time with-
out running the engine. If you drain the car’s battery
too far, you may not be able to start the engine and
this can reduce the service life of the battery.
1. Press the [POWER] button.
2. The settings are displayed on the control unit
display.
3. Press the [POWER] button to turn off the
power.
Switching input source
Change the settings to suit the input signal
source.
• The initial setting is [DIGITAL1].
Press the [SOURCE] button.
Each time the [SOURCE] button is pressed, the
indications change as shown below.
[DIGITAL1] → [DIGITAL2] → [ANALOG1] →
[ANALOG2]
→ [DIGITAL1]
• The original mode is resumed when the but-
ton is not pressed during a 7 second inter-
val.
Notes:
• Sound may be interrupted for a very short period
while audio format is being distinguished.
• If skip or pause operations are performed on the
DVD player while sound is being played back,
noise may be heard for a brief interval.
●
DIGITAL1 (Digital 1):
Use this setting when playing back digital input
sources connected using an optical-fiber cable
to digital input 1.
●
DIGITAL2 (Digital 2):
Use this setting when playing back digital input
sources connected using an optical-fiber cable
to digital input 2.
●
ANALOG1 (Analog 1):
Use this setting when playing back an analog
input source connected using RCA plugs.
●
ANALOG2 (Analog 2):
Use this setting when playing back an analog
input source connected using a CeNET cable.
Adjusting the sound volume
CAUTION
The sound volume on a DVD video disc can
become very loud. For that reason, turn up
the sound volume gently when the video im-
age is displayed.
Press the [VOL] buttons on the control unit.
Note:
• Adjust the audio volume using the controls on this
control unit. The audio volume cannot be adjusted
using the Center Unit controls.
Changing display settings
Press the [ ] or [ ] [DISP] button.
Each time the [ ] or [ ] [DISP] button are
pressed, the indications change as shown below.
[SS 1] → [SS 2] → [DISP OFF] → [PROGRAM]
→ [SS 1]
● SS1: displays the dolphin.
● SS2: displays the airplane
● DISP OFF: the display is off.
● PROGRAM (Program):
Indicates the format of the signals input from
the DIGITAL connectors.
• MONO: Monaural sound
• STEREO: Stereo sound
Note: Be sure to read this chapter referring to the front diagrams of
chapter “3. CONTROLS” on page 5 (unfold).
:increases the sound volume.
:decreases the sound volume
POWER D S F ADJUST A-MODE SOURCE
[POWER]
[DSF]
[ADJUST]
[A-MODE]
[SOURCE]
[ENT]
[MUTE]
[DISP]
[VOL]
■
Control unit / Module de commande / Unidad de control /
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.
Remarque: Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.
Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.
280-7804-00_02-08(En) 2/22/02, 2:05 PM 4