Crosley Radio Crosley Composer CD Recorder CR247 - Manual (Page 8)

8 7
Playing a Cassette
Accessory: ADAPTER FOR 45 RPM
To Fast Forward or Rewind
Turntable Operation
1
Press the FUNCTION button (17/68) to set the
unit to Phono mode.
2
Set the SPEED CONTROL SWITCH (34) to
the correct speed (331/3, 45 or 78 rpm) for the
selected record.
3
Use the CUE LEVER (32) to raise the tone arm
off its rest. Move the tone arm over the record
and use the cue lever to lower it to the point
you want the record to start.
4
At the end of the record, the tone arm will return
to its rest.
NOTE:The turntable and cassette players both operate
in the same mode. Make sure the cassette
player is in STOP mode when listening to a
record.
To play the 45rpm record, place the ADAPTER (44)
on the spindle.
Basic Operation
1
While in Phono mode, press the
STOP/EJECT(25) button on the cassette player
to open the cassette door.
2
Insert a prerecorded cassette tape into the
cassette door.
3
Press the PLAY button (28) to begin play.
4
To stop playback, press the STOP/EJECT (25)
button.
5
Press the STOP/EJECT (25) button again to
eject the cassette.
1
While playback is stopped, press the FAST
FORWARD (26) or REWIND (27) button to fast
forward or rewind the cassette.
2
Once the desired position is reached on the
cassette, press the STOP/EJECT (25) button
to stop the cassette.
3
Press the PLAY (28) button to begin play.
NOTE: The cassette player plays the side of the
cassette facing away from the unit. To
play the other side of the cassette, you
must eject the cassette and turn it over.
Antenna
1
Make sure the unit is plugged in correctly to an
AC outlet.
2
Press the POWER button (20) to turn the power
on.
3
Once the power is turned on, press the
FUNCTION button (17/68) to switch between
Tuner/CD/Phono/Aux. When switching between
functions, wait 1 second after pressing the
function button before pressing it again. This
gives the unit time to load the correct information
for the selected function.
4
While listening to any of the above functions,
you may change the tone of the music by
pressing the EQ button (18/67). Each press of
the EQ button will toggle between the following
settings:
Basic Operation
Outdoor Antenna Grounding
1
Press the FUNCTION button (17/68) to set the
unit to Tuner mode
2
Press the BAND button (19/58) to select the
desired tuning band (AM/FM).
3
Press the (11) or (9) button to select a
station,To use the remote to select a station, use
the (62) or (50) buttons.
4
Adjust the volume to the desired listening level.
1
Tune into the station that you want to program
into memory.
2
Press the PROGRAM button (12/47), Memory
will flash on the LCD.
3
Press the (11/64) or (9/52) buttons to
select the desired memory location.
4
Press the Program button again to store the
station into memory.
5
Once you have the presets stored, press the
PRESET UP + (10/54) or the PRESET – (8/65)
to select the stored stations.
Antenna: for extennal FM reception, the unit is
provided with a FM ANTENNA WIRE (43), move the
wire until the reception is clear and with no inter-
ferences. For AM reception, the unit is provided with
a directional build-in ferrite antenna. Rotate the set
to find the position in which the best reception is
obtained.
General
If an outside antenna is connected to the receiver,
be sure the antenna system is grounded so as to
provide some protection against voltage surges and
buit-up static charges. Article 610 of the National
Electrical Code, ANSI/NFPA 70, provides information
with regard to proper grounding of the mast and
supporting conductors, location of antenna-discharge
unit, connection to grounding electrodes, and
requirements for the grounding electrode. See figure:
NOTE: Please use outside antenna for better reception.
FM Antenna Wire (43) AM Loop Antenna (42)
GROUND CLAMP
ELECTR C
SERVICE
EQUPMENT
ANTENNA
LEAD IN WIRE
ANTENNA
DISCHARGE UN T
GROUNDING
CONDUCTORS
GROUND CLAMPS
POWER SERVICE GROUND NG
ELECTRODE SYSTEM
Radio Operation
Programming Preset Stations
FLAT CLASSIC POP
JAZZ ROCK