Rev-A-Shelf DOOR MOUNTING BRACKETS TAPE - Manual

ALTERNATIVE “EASY INSTALL”
Top Mount Pull-Out Waste Containers WITH
DOOR MOUNTING BRACKETS TAPE
Your Door Mount Kit also includes two pieces of specially
designed two-sided tape. Follow the directions below for
quick and easy installation method that is usually much
faster for “In-Home” retro-fitting:
Step 1: Follow steps one through six on “Installation Instructions” (front page).
Paso 1: Siga los pasos uno a seis en las “Instrucciones de instalación” (la primer página).
Étape 1: Suivre les étapes de un à six de la Notice d’installation (page de couverture).
Step 2: Make sure you have correctly
selected the correct positioning of our
Door Bracket Flanges so that the mounting
holes will be located in a position to insert
the fastners (screws) in the thick, outside
section of the door panel.
Paso 2: Asegúrese de elegir la posición
correcta para las bridas de soporte de puerta para que la posición de los
agujeros de montaje permita introducir los sujetadores (tornillos) en la
parte exterior más gruesa del panel de la puerta.
Étape 2: Veiller à correctement sélectionner l’emplacement des brides de
support de porte de manière à ce que les trous de montage permettent de
visser les vis dans la partie externe épaisse du panneau de porte.
Step 3: Peel off one of each of the (2) tape strips provided and carefully
place over the door bracket flanges.
Paso 3: Pele una cara en cada una de las dos (2) cintas adhesivas y
adhiéralas cuidadosamente sobre las bridas de soporte.
Étape 3: Enlever le papier d’un des côtés des deux (2) bandes adhésives et
positionner les bandes soigneusement au-dessus des brides de support
de porte.
Step 4: Loosen the 4 bolts (2 each side) that connect the door brackets to
the product member bracket. Pull them forward (towards you) and tighten
them. This will insure that the face of the door bracket extends slightly
outside of the front frame of your cabinet.
Paso 4: Afloje los 4 pernos (2 en cada lado) que unen los soportes de
puerta al soporte de la placa del producto. Tire de ellos (hacia usted) y
apriételos. Esto permitirá que la cara del soporte de puerta sobresalga
ligeramente hacia fuera del bastidor delantero de su armario.
Étape 4: Desserrer les quatre boulons (deux de chaque côté) qui
raccordent les supports de porte au support du produit. Les tirer vers soi
et les resserrer. Ceci assure que la face du support de porte s’étend
légèrement au-delà du cadre frontal de l’armoire.
Step 5: Peel off the exterior layer of tape. Now
carefully line up your desired door position by
eyesight using the drawer above and any cabinets
to your left or right as a gauge for correct alignment.
Paso 5: Pele la cara exterior de la cinta adhesiva.
Alinee visualmente la puerta con cuidado, utilizando
la gaveta de arriba y cualquier otro armario situado
a la izquierda o derecha como referencia para
alinearla correctamente.
Étape 5: Enlever le papier recouvrant la face externe de la bande
adhésive. Aligner ensuite soigneusement la porte en utilisant le tiroir du
dessus et les armoires sur les côtés, le cas échéant, comme point de repère
d’alignement.
Step 6: Press the door firmly onto the door brackets with the two sided
tape. Put pressure directly on the sides, in position with the brackets to
allow for good adhension.
Paso 6: Presione firmemente la puerta contra la cinta adhesiva colocada
en los soportes de puerta. Aplique la presión directamente sobre los
costados sobre los soportes para que se adhiera bien.
Étape 6: Pousser fermement la porte sur les supports de porte munis de
bande adhésive. Bien appuyer sur les côtés à hauteur des supports pour
assurer une bonne adhésion.
Step 7: Carefully pull the door out from the sides and mark several holes on
each side through the brackets as a reference in case the tape does not hold
the bracket to the door.
Paso 7: Separe cuidadosamente la puerta de los costados y haga marcas de
referencia a través de varios orificios a cada lado de los soportes en caso de
que la cinta adhesiva no los adhiera a la puerta.
Étape 7: Tirer prudemment la porte en la saisissant par les côtés et marquer
plusieurs trous dans les deux supports comme point de repère au cas où la
bande adhésive ne suffirait pas pour maintenir le support à la porte.
Step 8: Fasten the brackets to the door using the tape as a temporary hold
while you insert #6 x 1/2” wood screws.
Paso 8: Fije los soportes a la puerta utilizando la cinta adhesiva como
fijador temporal mientras introduce tornillos para madera núm. 6 x 1/2 pulg.
Étape 8: Attacher les supports à la porte en utilisant la bande adhésive
comme système de maintien temporaire pendant l’insertion des vis à bois
no 6 x 1/2 po.
Step 9: -Final adjustment
-Loosen the four bolts and make adjustments if necessary.
(See Step 9 on previous page)
Paso 9: • Ajuste final
• Afloje los cuatro pernos y haga los ajustes que sean necesarios.
(Ver el paso 9 en la página anterior)
Étape 9: -Réglage final
-Desserrer les quatre boulons et faites les réglages nécessaires.
(Voir l’étape 9 à la page précédente)
STEP 5:
Peel off the exterior layer of tape.
Now carefully line up your desired
door position by eyesight using
the drawer above and any cabinets
to your left or right as a gauge for
correct alignment.
STEP 6:
Press the door firmly onto the
door brackets with the two sided
tape. Put pressure directly on the
sides, in position with the brackets
to allow for good adhesion.
ALTERNATIVE “EASY INSTALL”
for Top Mount Pull-Out Waste Containers WITH
Door Mounting Brackets Tape
Your Door Mount Kit also includes two pieces of specially designed two-sided tape. Follow the directions below for quick and easy installation
method that is usually much faster for “In-Home” retro-fitting:
STEP 1:
Follow steps one through six on “Installation
Instructions” (front page).
STEP 3:
Peel off one side of each of the (2) tape strips provided and
carefully place over the door bracket flanges
STEP 2:
Make sure you have correctly
selected the correct positioning of
our Door Bracket Flanges so that
the mounting holes will be located
in a position to insert the fastners
(screws) in the thick, outside
section of the door panel.
STEP 4:
Loosen the 4 bolts (2 each side) that connect the door brackets to
the product member bracket. Pull them forward (towards you) and
tighten them. This will insure that the face of the door bracket
extends slightly outside of the front frame of your cabinet.
STEP 9:
• Final adjustment
• Loosen the four bolts and make adjustments if necessary.
(See Step 9 on previous page)
STEP 7:
Carefully pull the door out from the sides and mark several
holes on each side through the brackets as a reference in
case the tape does not hold the bracket to the door.
STEP 8:
Fasten the brackets to the door
using the tape as a temporary
hold while you insert #6 x 1/2"
wood screws.
STEP 5:
Peel off the exterior layer of tape.
Now carefully line up your desired
door position by eyesight using
the drawer above and any cabinets
to your left or right as a gauge for
correct alignment.
STEP 6:
Press the door firmly onto the
door brackets with the two sided
tape. Put pressure directly on the
sides, in position with the brackets
to allow for good adhesion.
ALTERNATIVE “EASY INSTALL”
for Top Mount Pull-Out Waste Containers WITH
Door Mounting Brackets Tape
Your Door Mount Kit also includes two pieces of specially designed two-sided tape. Follow the directions below for quick and easy installation
method that is usually much faster for “In-Home” retro-fitting:
STEP 1:
Follow steps one through six on “Installation
Instructions” (front page).
STEP 3:
Peel off one side of each of the (2) tape strips provided and
carefully place over the door bracket flanges
STEP 2:
Make sure you have correctly
selected the correct positioning of
our Door Bracket Flanges so that
the mounting holes will be located
in a position to insert the fastners
(screws) in the thick, outside
section of the door panel.
STEP 4:
Loosen the 4 bolts (2 each side) that connect the door brackets to
the product member bracket. Pull them forward (towards you) and
tighten them. This will insure that the face of the door bracket
extends slightly outside of the front frame of your cabinet.
STEP 9:
• Final adjustment
• Loosen the four bolts and make adjustments if necessary.
(See Step 9 on previous page)
STEP 7:
Carefully pull the door out from the sides and mark several
holes on each side through the brackets as a reference in
case the tape does not hold the bracket to the door.
STEP 8:
Fasten the brackets to the door
using the tape as a temporary
hold while you insert #6 x 1/2"
wood screws.
STEP 5:
Peel off the exterior layer of tape.
Now carefully line up your desired
door position by eyesight using
the drawer above and any cabinets
to your left or right as a gauge for
correct alignment.
STEP 6:
Press the door firmly onto the
door brackets with the two sided
tape. Put pressure directly on the
sides, in position with the brackets
to allow for good adhesion.
ALTERNATIVE “EASY INSTALL”
for Top Mount Pull-Out Waste Containers WITH
Door Mounting Brackets Tape
Your Door Mount Kit also includes two pieces of specially designed two-sided tape. Follow the directions below for quick and easy installation
method that is usually much faster for “In-Home” retro-fitting:
STEP 1:
Follow steps one through six on “Installation
Instructions” (front page).
STEP 3:
Peel off one side of each of the (2) tape strips provided and
carefully place over the door bracket flanges
STEP 2:
Make sure you have correctly
selected the correct positioning of
our Door Bracket Flanges so that
the mounting holes will be located
in a position to insert the fastners
(screws) in the thick, outside
section of the door panel.
STEP 4:
Loosen the 4 bolts (2 each side) that connect the door brackets to
the product member bracket. Pull them forward (towards you) and
tighten them. This will insure that the face of the door bracket
extends slightly outside of the front frame of your cabinet.
STEP 9:
• Final adjustment
• Loosen the four bolts and make adjustments if necessary.
(See Step 9 on previous page)
STEP 7:
Carefully pull the door out from the sides and mark several
holes on each side through the brackets as a reference in
case the tape does not hold the bracket to the door.
STEP 8:
Fasten the brackets to the door
using the tape as a temporary
hold while you insert #6 x 1/2"
wood screws.
STEP 5:
Peel off the exterior layer of tape.
Now carefully line up your desired
door position by eyesight using
the drawer above and any cabinets
to your left or right as a gauge for
correct alignment.
STEP 6:
Press the door firmly onto the
door brackets with the two sided
tape. Put pressure directly on the
sides, in position with the brackets
to allow for good adhesion.
ALTERNATIVE “EASY INSTALL”
for Top Mount Pull-Out Waste Containers WITH
Door Mounting Brackets Tape
Your Door Mount Kit also includes two pieces of specially designed two-sided tape. Follow the directions below for quick and easy installation
method that is usually much faster for “In-Home” retro-fitting:
STEP 1:
Follow steps one through six on “Installation
Instructions” (front page).
STEP 3:
Peel off one side of each of the (2) tape strips provided and
carefully place over the door bracket flanges
STEP 2:
Make sure you have correctly
selected the correct positioning of
our Door Bracket Flanges so that
the mounting holes will be located
in a position to insert the fastners
(screws) in the thick, outside
section of the door panel.
STEP 4:
Loosen the 4 bolts (2 each side) that connect the door brackets to
the product member bracket. Pull them forward (towards you) and
tighten them. This will insure that the face of the door bracket
extends slightly outside of the front frame of your cabinet.
STEP 9:
• Final adjustment
• Loosen the four bolts and make adjustments if necessary.
(See Step 9 on previous page)
STEP 7:
Carefully pull the door out from the sides and mark several
holes on each side through the brackets as a reference in
case the tape does not hold the bracket to the door.
STEP 8:
Fasten the brackets to the door
using the tape as a temporary
hold while you insert #6 x 1/2"
wood screws.
STEP 5:
Peel off the exterior layer of tape.
Now carefully line up your desired
door position by eyesight using
the drawer above and any cabinets
to your left or right as a gauge for
correct alignment.
STEP 6:
Press the door firmly onto the
door brackets with the two sided
tape. Put pressure directly on the
sides, in position with the brackets
to allow for good adhesion.
ALTERNATIVE “EASY INSTALL”
for Top Mount Pull-Out Waste Containers WITH
Door Mounting Brackets Tape
Your Door Mount Kit also includes two pieces of specially designed two-sided tape. Follow the directions below for quick and easy installation
method that is usually much faster for “In-Home” retro-fitting:
STEP 1:
Follow steps one through six on “Installation
Instructions” (front page).
STEP 3:
Peel off one side of each of the (2) tape strips provided and
carefully place over the door bracket flanges
STEP 2:
Make sure you have correctly
selected the correct positioning of
our Door Bracket Flanges so that
the mounting holes will be located
in a position to insert the fastners
(screws) in the thick, outside
section of the door panel.
STEP 4:
Loosen the 4 bolts (2 each side) that connect the door brackets to
the product member bracket. Pull them forward (towards you) and
tighten them. This will insure that the face of the door bracket
extends slightly outside of the front frame of your cabinet.
STEP 9:
• Final adjustment
• Loosen the four bolts and make adjustments if necessary.
(See Step 9 on previous page)
STEP 7:
Carefully pull the door out from the sides and mark several
holes on each side through the brackets as a reference in
case the tape does not hold the bracket to the door.
STEP 8:
Fasten the brackets to the door
using the tape as a temporary
hold while you insert #6 x 1/2"
wood screws.
STEP 5:
Peel off the exterior layer of tape.
Now carefully line up your desired
door position by eyesight using
the drawer above and any cabinets
to your left or right as a gauge for
correct alignment.
STEP 6:
Press the door firmly onto the
door brackets with the two sided
tape. Put pressure directly on the
sides, in position with the brackets
to allow for good adhesion.
ALTERNATIVE “EASY INSTALL”
for Top Mount Pull-Out Waste Containers WITH
Door Mounting Brackets Tape
Your Door Mount Kit also includes two pieces of specially designed two-sided tape. Follow the directions below for quick and easy installation
method that is usually much faster for “In-Home” retro-fitting:
STEP 1:
Follow steps one through six on “Installation
Instructions” (front page).
STEP 3:
Peel off one side of each of the (2) tape strips provided and
carefully place over the door bracket flanges
STEP 2:
Make sure you have correctly
selected the correct positioning of
our Door Bracket Flanges so that
the mounting holes will be located
in a position to insert the fastners
(screws) in the thick, outside
section of the door panel.
STEP 4:
Loosen the 4 bolts (2 each side) that connect the door brackets to
the product member bracket. Pull them forward (towards you) and
tighten them. This will insure that the face of the door bracket
extends slightly outside of the front frame of your cabinet.
STEP 9:
• Final adjustment
• Loosen the four bolts and make adjustments if necessary.
(See Step 9 on previous page)
STEP 7:
Carefully pull the door out from the sides and mark several
holes on each side through the brackets as a reference in
case the tape does not hold the bracket to the door.
STEP 8:
Fasten the brackets to the door
using the tape as a temporary
hold while you insert #6 x 1/2"
wood screws.
I-WCTMDMEASY-TRI
12400 Earl Jones Way, Louisville, KY 40299
(800) 626-1126 • rev-a-shelf.com