SilentKnight SK-Zone-6 Addressable Six Zone Interface Module User Manual
Sk-zone-6 six zone interface module, Installation and maintenance instructions
SK-460-008
1
I56-3441-000
INSTALLATION AND MAINTENANCE INSTRUCTIONS
I56-344
1-000
7550 Meridian Circle, Maple Grove, MN 55369-4927
763.493.6455, 800.328.0103; Fax: 763.493.6475
http://www.silentknight.com
SK-Zone-6
Six Zone Interface Module
SPECIFICATIONS
Normal Operating Voltage:
15-32 VDC
Stand-By Current:
2 mA
Alarm Current:
40 mA (assumes all six LEDs solid on)
Temperature Range:
32ºF to 120ºF ( 0ºC to 49ºC)
Humidity:
10 to 93% Non-condensing
Dimensions:
6.8˝ H x 5.8˝ W x 1.0˝ D
Accessories:
IDP-ACB Cabinet and chassis
Wire Gauge:
12-18 AWG
Max. IDC Wiring Resistance:
25 ohms
External Power Supply Voltage:
Regulated 24VDC
Ripple Voltage:
0.1 volts RMS maximum
IDC:
(Supervised and power limited)
DC Voltage:
18-28 volts power limited
Frequency:
DC
Current:
90mA per circuit
BEFORE INSTALLING
If the modules will be installed in an existing operational system, inform the
operator and local authority that the system will be temporarily out of service.
Disconnect the power to the control panel before installing the modules. This
system contains static sensitive components. Always ground yourself with a
proper wrist strap before handling any circuits so that static charges are re-
moved from the body. The module housing should also be grounded.
NOTICE: This manual should be left with the owner/user of this equipment.
GENERAL DESCRIPTION
The SK-Zone-6 Six Zone Interface Module is intended for use in an intelli-
gent alarm system. Each module provides an interface between the intelligent
alarm system and a conventional alarm system loop. A common SLC input is
used for all modules, and the initiating device loops share a common super-
visory supply and ground. Otherwise, each monitor operates independently
from the others. Each module has its own unique address.
A pair of rotary code switches is used to set the address of the first module
from 01 to 94 (or 01 to 154 for panels that support 159 addresses). The re-
maining modules are automatically assigned to the next five higher addresses.
Provisions are included for disabling a maximum of two unused modules to
release the addresses to be used elsewhere. Each module also has panel con-
trolled bicolor LED indicators. The panel can cause the LEDs to blink, latch
on, or latch off.
DET.
MODEL
COMP. ID DETECTOR
MANUFACTURER
BASE MODEL MAX
DET.
1151
A
SYSTEM SENSOR
B110LP, B401
20
1451
A
SYSTEM SENSOR
B401, B401B
20
1451DH
A
SYSTEM SENSOR
DH400
20
2151
A
SYSTEM SENSOR
B110LP, B401
20
2451
A
SYSTEM SENSOR
DH400, B401B,
B401
20
2451TH
A
SYSTEM SENSOR
B401, B401B
20
5451
A
SYSTEM SENSOR
B401
20
1100
A
SYSTEM SENSOR
N/A
20
1400
A
SYSTEM SENSOR
N/A
20
**2100AT
A
SYSTEM SENSOR
N/A
20
2100B
A
SYSTEM SENSOR
N/A
20
2100D
A
SYSTEM SENSOR
N/A
20
2100S
A
SYSTEM SENSOR
N/A
20
2100TB
A
SYSTEM SENSOR
N/A
20
2100TD
A
SYSTEM SENSOR
N/A
20
2100TS
A
SYSTEM SENSOR
N/A
20
2300B
A
SYSTEM SENSOR
N/A
20
2300TB
A
SYSTEM SENSOR
N/A
20
2400
A
SYSTEM SENSOR
N/A
20
2400TH
A
SYSTEM SENSOR
N/A
20
*2W-B
A
SYSTEM SENSOR
N/A
20
*2W-TB
A
SYSTEM SENSOR
N/A
20
DH100LP
A
SYSTEM SENSOR
N/A
20
*Class B, Style B only; **No Accessory will be supported by 2100AT
COMPATIBLE TwO-wIRE SySTEM SENSOR SMOKE DETECTORS FOR
USE wITh SK-ZONE-6 wITh ZONE IDENTIFIER A
INCLUDED:
(5) 1 x 4 Terminal Blocks (2) 11/4˝ Stand offs (3) Shunts
(4) Machine Screws (1) Long Power Supply Jumper
(2) Nuts
(6) 3.9k Ohm
End of Line Resistors
ShIPPED ON BOARD:
(2) Shunts in Class A/B position
(Shipped in Class B position, remove shunts for Class A)