Cuisinart 11-Cup Series - Manual (Page 16)

Processing dry
ingredients:
Put the flour in the work
bowl with all the other dry
ingredients. If the recipe
calls for herbs, oil or solid
fats like butter, add them
with the flour. Turn the
machine on and let it run
for about 20 seconds.
(Cheese, nuts and raisins
may be added with the dry
ingredients or during the
final kneading. To leave
them almost whole, add
them 5 seconds before you
stop kneading. For a finer
texture, add them sooner.)
Adding liquids:
All liquid should be added
through the feed tube while
the machine is running.
Add liquid in a slow, steady
stream, only as fast as dry
ingredients absorb it. If
liquid sloshes or splatters,
stop adding it but do not
turn off the machine. Wait
until ingredients in bowl
have mixed, then add
remaining liquid slowly.
Pour liquid onto dough as
it passes under feed tube
opening. Do not pour
liquid directly onto bottom
of bowl.
Follow the recipe carefully.
It is important to add
enough liquid to make the
dough soft enough to
knead. Kneading dough
that is too stiff can strain
the machine.
All liquid, except that which
is used to activate yeast,
should be cold, to minimize
the possibility of overheating
the dough. You must never
knead a yeast dough to a
temperature higher than
100˚F (37˚C). Doing so will
slow or even prevent the
action of the yeast.
Kneading bread dough:
Do not try to use the
machine to knead dough
that is too stiff to knead
comfortably by hand. Doing
so can strain the machine.
After the dough starts to
clean the inside of the work
bowl completely and forms
a ball, process it for 60
seconds to knead it. Stop
the machine and test the
dough to be sure it’s prop-
erly kneaded. Typical bread
dough should have a soft,
pliable texture and it should
feel slightly sticky. Stretch
the dough with your hands
to test it. If it feels hard,
lumpy or uneven, continue
processing until it feels
uniformly soft and pliable.
Make sure that the blade is
firmly pressed back into
place after removing the
dough to test it.
Kneading sweet dough:
Process dough for at least
30 seconds after all the
ingredients have been
incorporated. It will not
clean the inside of the work
bowl. If necessary, scrape
the bowl and process for 5
more seconds.
Rising:
Put the dough in a large,
lightly floured resealable
plastic bag. Squeeze out all
the air and close tightly,
allowing space for the
dough to rise.
Or put the ball of dough in
a large bowl coated with
soft butter or vegetable oil.
Roll the dough around to
coat its entire surface. Cover
it with a damp towel or a
piece of oiled plastic wrap.
Let it rise in a warm,
draft-free place, about 80˚F
(26˚C). The rising time is
usually about 1-1/2 hours
but will vary from 45
minutes to several hours,
depending on the type of
flour and the humidity of the
air. To test if the dough has
risen enough, stick a finger
in it. An indentation should
remain. If it doesn’t, let the
dough rise more and test
again.
When it has risen enough,
punch the dough down.
Shaping, finishing
and baking:
If you shape the dough
in loaf pans, fill pans only
half full. Let rise until dough
is just slightly above the
top of the pan. If shaping
free-form loaves, let them
rise on an oiled baking
sheet until at least
doubled in bulk.
Making consecutive
batches:
You can make several
batches of bread dough
in a row. The motor in
the Premier
™ 11-Cup Food
Processor is extremely
efficient.
TYPICAL
BREAD DOUGH
PROBLEMS AND
SOLUTIONS
If dough blade doesn’t
incorporate ingredients:
Always start processor
before adding liquid. Add
liquid in slow, steady
stream, only as fast as dry
ingredients absorb it. If you
hear liquid sloshing, stop
adding it but do not turn off
machine. Instead, wait until
ingredients in work bowl
have mixed, then add
15
02CU13445 DLC-2011 IB REV 8/4/03 1:50 PM Page 16