Sportline 490 Heat Sensor Timer - Manual (Page 2)

HEAT SENSOR STOP WATCH
• AVOID getting the stop watch wet. This unit is water resistant, not water proof.
• NEVER attempt to disassemble or service your unit.
• DO NOT expose the unit to extreme heat, shocks, magnetic fields, electrical noise,
strong vibration or long-term exposure to direct sunlight.
• DO NOT drop or step on the stop watch.
• TO CLEAN the unit: wipe with a lightly moistened cloth. Apply mild soap to the
area if there are stubborn stains or marks. Do not expose the unit to strong
chemicals such as gasoline, cleaning solvents, acetone, alcohol, insect repellents,
as they may damage the unit’s seal, case and/or finish.
• STORE the unit in a dry place when you are not using it.
www.sportline.com
13- REPLACING THE BATTERY 12- CARE & MAINTENANCE
The Sportline Heat Sensor Stop Watch uses one CR2032 3V lithium battery.
Battery replacement will be required from time to time, and should occur when:
1. The display fades in part or completely
2. The timing function will not activate
TO REPLACE THE BATTERY:
1. Remove the screws on the back of the unit with a small phillips screwdriver and
remove te back cover.
2. Remove the exhausted battery from the unit, and insert a new battery (be sure
to place the positive (+) side of the battery is visible, facing toward the battery
compartment cover).
3. Replace the back cover and replace the screws with a small phillips screwdriver.
14- BATTERY SAFETY INFORMATION
CAUTION – BATTERY SAFETY INFORMATION
• Non-rechargeable batteries are not to be recharged
• Rechargeable batteries must be removed before recharging
• Rechargeable batteries should only be recharged under adult supervision
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium)
batteries
• Exhausted batteries are to be removed
• Do not mix old and new batteries
• Do not dispose of batteries in fire; batteries may explode or leak
• Do not dispose of product in fire; batteries may explode or leak
• If this product will not be used for an extended period of time, remove the bat-
teries from the product
• The supply terminals are not to be short-circuited
• Batteries are to be inserted with correct polarity
• Clean the battery contacts and also those of the product prior to battery instal-
lation
• As always, dispose of batteries in an eco-friendly manner
The purpose of the crossed-out wheelie bin symbol is to remind us that most electrical products,
and batteries, contain trace elements (including Mercury – Hg, Cadmium – Cd and Lead – Pb)
which could be harmful to our environment and therefore our health. We must all be careful to
dispose of them responsibly in a specifically designated way – either using a collection scheme or
into the correctly labeled civic amenity (NOT into general waste) – this will help your local author-
ity to arrange to recycle or dispose of them in the appropriate manner.
15- WARRANTY
GUARANTEE CERTIFICATE – FOR PURCHASES MADE IN THE U.S.
If at any time within one (1) year from the purchase date of this product, it fails to
perform properly because of defects in material or manufacturing, return it prepaid to:
EB SPORT GROUP, 585 OAK RIDGE ROAD, HAZLETON, PA 18202
Complete this Guarantee Certificate and enclose it (or a copy of it) with the product.
(PLEASE PRINT CLEARLY)
NAME
PHONE
ADDRESS
STORE PURCHASED FROM
DATE OF PURCHASE PURCHASE PRICE
STATE ZIP
PROBLEM WITH PRODUCT
REPLACEMENT
This product has been carefully designed, manufactured and packaged. If any parts are missing or damaged, please
contact us at the address above and we will replace the unit at no charge. (Guarantee does not cover crystal or battery.)
©2011 Distributed by Sportline®, Hazleton, PA 18202
FOR PURCHASES MADE IN THE UK:
Should you experience problems with this item, please return it to the point of
purchase. This will not affect your statutory rights. Alternatively return it to the
address shown below for a repair/replacement.
EB Brands UK, Berkeley Business Park, Wainwright Road,
Worcester WR4 9FA
www.sportline.com
Distributed in the UK by EB Brands UK, Worcester WR4 9FA
8- SETTING THE TIME AND DATE
SETTING TIME AND DATE
1. In Time mode, PRESS & HOLD the RECALL key for 2 seconds to enter the
programming sequence.
2. Adjust Seconds by PRESSING the START/STOP key. PRESS the LAP/SPLIT key
to accept value and advance to set Minutes.
3. Adjust Minutes by PRESSING the START/STOP key. PRESS the LAP/SPLIT key
to accept value and advance to set Hour.
4. Adjust Hour by PRESSING the START/STOP key. PRESS the LAP/SPLIT key to
accept value and advance to set Year.
5. Adjust Year by PRESSING the START/STOP key. PRESS the LAP/SPLIT key to
accept value and advance to set Month.
6. Adjust Month by PRESSING the START/STOP key. PRESS the LAP/SPLIT key
to accept value and advance to set Day of Month.
7. Adjust Day by PRESSING the START/STOP key. PRESS the LAP/SPLIT key to
accept value and advance to set 12/24-hour time format.
8. Select 12- or 24-hour Time Format by PRESSING the START/STOP key. PRESS
the LAP/SPLIT key to accept.
9. PRESS the RECALL key to exit the programming sequence. Time/Date is now
programmed.
11- STOP WATCH FUNCTIONS
• Calendar display: month, date and day of the week
• 12 or 24-hour time format
• Daily alarm
• Heat index
• Dew point
• Temperature and humidity display
• 10-hour, 30 lap/split chronograph with 1/100-second resolution
• Lap/split memory playback
• Countdown timer
• Water resistant
1 2 3
1 2 3
Turn Alarm ON/OFF:
PRESS START/STOP
in Alarm Mode
9- SETTING THE ALARM 10- SETTING THE COUNTDOWN TIMER
SETTING THE ALARM
1. In Alarm mode, PRESS & HOLD the RECALL key for 2 seconds to enter the
programming sequence.
2. Adjust Hour by PRESSING the START/STOP key. PRESS the LAP/SPLIT key to
accept value and advance to set Minute.
3. Adjust Minutes by PRESSING the START/STOP key. PRESS the LAP/SPLIT key
to accept value and advance to set Hour.
4. PRESS the RECALL key to exit the programming sequence. Time/Date is now
programmed.
TO ACTIVATE/DEACTIVATE ALARM
1. In Alarm mode, PRESS the START/STOP key to turn Alarm ON/OFF. When
activated, the alarm icon will be visible.
SETTING THE COUNTDOWN TIMER
1. In Countdown Timer mode, PRESS & HOLD the RECALL key for 2 seconds to
enter the programming sequence.
2. Adjust Hour by PRESSING the START/STOP key. PRESS the LAP/SPLIT key to
accept value and advance to set Minute.
3. Adjust Minutes by PRESSING the START/STOP key. PRESS the LAP/SPLIT key
to accept value and advance to set Seconds.
4. Adjust Seconds by PRESSING the START/STOP key. PRESS the LAP/SPLIT key
to accept value
5. PRESS the RECALL key to exit the programming sequence. Countdown Timer
is now programmed.
USING THE COUNTDOWN TIMER:
1. PRESS START/STOP to begin counting down.
2. PRESS LAP/RESET to reset to original time.