Studio Projects CS5 - Manual (Page 6)

This microphone has a serial number on the rear. Please record the model number and serial number and
retain them for your records.
Model number
Serial number
NOTE — This apparatus does not exceed the Class A/Class B (whichever is applicable) limits for radio noise
emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of
Communications.
ATTENTION — Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant las limites
applicables aux appareils numériques de class A/de class B (selon le cas) prescrites dans le réglement sur le brouil-
lage radioélectrique édicté par les ministere des communications du Canada.
These limits are designed to provide reasonable protection against harmful interference in a commercial/residen-
tial installation respectively. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio commu-
nications. There is no guarantee that interference will not occur in a particular installation. If this equipment does
cause interference to radio or television equipment reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by any combination of the following measures:
(1) Relocate or reorient the receiving antenna (2) Increase the separation between the equipment and the re-
ceiver (3) Plug the equipment into an outlet on a circuit different from that to which the receiver is connected (4)
Consult your dealer or experienced radio/television technician for additional assistance.
CAUTION — Changes or modifications to this equipment not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water. Do not expose to drips or splashes. Do not place any objects filled with
liquids, such as vases, on the apparatus.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Do not install this apparatus in a confined space such as a book case
or similar unit. Install only in racks designed for the purpose and in accordance with manufacturers’ instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus combina-
tion to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
15. Apparatus designed with Class-I construction must be connected to a mains socket outlet with a protective
earthing connection (the third grounding prong).
16. This apparatus may be equipped with a single-pole, rockerstyle AC mains power switch. If so this switch is
located on the front panel and should remain readily accessible to the user.
17. The manufacturer reserves the right to change the technical specification of the product without prior
notice.
NOTES
cs_series_manual.indd 12-13 1/25/07 11:31:26 AM