Studio Projects VTB1 Manual - Manual (Page 4)

7
PROBLEMS
Studio Projects electronics are extremely resistant to physical damage, but
if the unit fails to work after being dropped, it should be returned in adequate
packing to the supplier. A double test and inspection system means that
manufacturing faults are non-existent but should any fault occur, it will be
repaired (or replaced) free of charge except where the fault has been
caused by physical damage. (SEE WARRANTY INFORMATION)
ORIGINS AND MANUFACTURE
Studio Projects Electronics are entirely designed in the USA. They are man-
ufactured in China by 797 Audio to a specification created by Studio Projects,
Torrance, California. All Studio Projects electronics are inspected and tested
at the factory, then inspected and tested again at PMI Audio Groups facility
prior to shipping. Studio Projects electronics meet the requirements of elec-
tronic equipment sold both in the USA, Canada, and the European Union. All
Studio Projects products are CE Approved, and all power supplies are UL
rated.
DECLARATION OF CONFORMITY
This analog audio processing equipment conforms to the standards and
requirements of the
European Economic Community.
The EC Harmonized standards that have been applied are;
a) Electrical equipment (safety) Regulations 1994 (S.I. 1994/3260)
b) Electromagnetic Compatibility Directive (89/336/EEC) incorporating
(S.I. 1992/2372)
6
TROUBLESHOOTING
1) The microphone doesn't work!
Have you got something plugged into the INSTRUMENT input or is the
mic/line set incorrectly? (this can disable the microphone input)
Is the phantom power on? (capacitor microphones).
If there is indication on the VU LED, is the output volume control turned
down?
2) Got signal going through but no output?
Is there enough signal? Use plenty of drive.
Is the output gain control turned up, and do you have a properly
working monitor system?
3) I don’t get any power!
Is the supplied power supply plugged in correctly? Make sure the
barrel connector is pushed all the way into the socket, and be sure you
have available power to the supply.
rate. No repair or replacement by Purchaser of any Product or part
thereof shall extend the warranty period as to the entire Product. The
specific warranty on the repaired part only shall be in effect for a period
of ninety (90) days following the repair or replacement of that part or the
remaining period of the Product warranty, whichever is greater.
2. Exclusive Remedy: Acceptance: Purchaser’s exclusive remedy and
PMI’s sole obligation is to supply (or pay for) all labor necessary to
repair any product found to be defective within the warranty period
and to supply, at no extra charge, new or rebuilt replacements for
defective parts. If repair or replacement fails to remedy the defect, then
and only in such an event, shall PMI exchange to Purchaser a new or
reconditioned unit. Purchaser’s failure to make a claim as provided in
paragraph 1 above or continued use of the product shall constitute an
unqualified acceptance of such Product and a waiver by Purchaser of
all claims thereto.
3. Exceptions to Limited warranty: PMI shall have no liability or obligation
to Purchaser with respect to any Product subjected to abuse, improper
use, negligence, accident, modification, failure of the end-user to follow
the operating and maintenance procedures outlined in the users manual,
attempted repair by non-qualified personnel, operation of the unit
outside of the published environmental and electrical parameters, or
if such products original identification (trademark, serial number) markings
have been defaced, altered, or removed. PMI excludes from warranty
coverage, Products sold AS IS and/or WITH ALL FAULTS and
excludes used products which have not been sold by PMI to the
Purchaser. PMI also excludes from warranty coverage consumables
such as fuses and batteries, etc.
4. Proof of purchase: The dealer’s dated bill of sale must be retained as
evidence or the date of purchase and to establish warranty eligibility
STUDIO PROJECTS LIMITED WARRANTY
THIS PRODUCT IS FOR PROFESSIONAL USE ONLY
PMI Audio Group warrants that all products will be free from defects in
material or workmanship:
A: For a period of (1) one year from the date of purchase (hereinafter the
labor warranty period), PMI Audio Group will repair or replace this Product if
determined to be defective. After the expiration of the labor warranty period,
the Purchaser must pay labor charges.
B: In addition, PMI Audio Group will supply, at no charge, replacements for
defective parts for a period of (one year) from the date of purchase. During
the labor warranty period, to repair the Product, Purchaser must return the
defective Product, freight prepaid, or deliver it to PMI Audio Group Service
Center. The product to be repaired is to be returned in either its original
carton or a similar package affording an equal degree of production. PMI
Audio Group will return the repaired Product freight prepaid to the
Purchaser. PMI Audio Group is not obligated to provide Purchaser with a
substitute unit during the warranty period or at any time.
CONDITIONS
1. Notification of claims: Warranty Service: If Purchaser discovers that the
Product has proven defective in material or workmanship, then written
notice with an explanation of the claim shall be given promptly by
Purchaser to PMI but all claims for warranty service must be made within
the warranty period. If after investigation PMI determines that the reported
problem was not covered by the warranty, Purchaser shall pay PMI for the
cost of investigating the problem at its then prevailing time-and-materials