Channel Plus COAXIAL CABLE PANEL 3308 User Manual
Page 3
IR Repeating System
IR
EMITTERS
POWER
15VDC
SYSTEM POWER
FROM
MODULATOR
VIDEO SYSTEM
Model 2171 IR Emitter
Compatible IR Targets
Model 2131
Model 2130A
Model 2132
With the model 3308, you can also control your video devices from any
room in the house.
Any or all 8 outputs may be connected to model
2100A wall plates. The wall plates interface with a variety of industry
standard IR targets. Direct your IR remote control at the IR target and
the 2173 IR emitter will repeat the IR signals in the media center.
IR control signals
from the bedroom …
IR control signals
from the bedroom …
Are repeated at the media
center. Change the DSS
channel or pause the
VCR from any room.
Are repeated at
the media
1
1
2
2
Normally, the IR emitters are also connected to Model 2100A wall
plates. But, if the coax panel is located in the media center, you may
choose to connect the emitters to a model 2184 IR breakout panel.
Both examples are shown below. The model 2184 plugs directly into
the 3308, replacing the power adaptor cable. The 2184 can drive up to
4 IR emitters.
If the coax panel is not located at the media center, you may add a
model 2010 remote power wall plate at the media center and connect
the 3308 and 2010 with a single coax cable. The model 2010 will power
the 3308, drive the IR emitters and deliver any modulator signals to the
3308. In addition, the 2010 has connectors for 2 IR emitters. (The
model 2174 IR expansion panel will expand each of these ports to
drive up to 4 IR emitters.)
Model 2173
Model 2173
Model 2100A
Model 2100A
Model 2100A
Model 2173
Model 2010
Model 2184
Model 2130A
Model 2132
Modulators may
be connected here.
The 2010 must be
powered as shown.
Model 2010 MUST be
connected to the ‘B’ port.
More modulators may be
connected to the ‘A’ port.
Max recommended
cable length 150’ (Total
of these two pieces.)
4
5
POWER
LED
EMITTER
LED
EMITTER
TARGET
TO
TV
TO
TV
POWER
LED
EMITTER
LED
EMITTER
TARGET
TO
TV
TO
TV
POWER
LED
EMITTER
LED
EMITTER
TARGET
TO
TV
TO
TV
IR targets must be connected
to a model 2100A wall plate.
IR targets must be connected
to a model 2100A wall plate.
DC block
When using IR repeating,
only a
or
may be directly connected
to a 3308 output.
2100A
DC block
IR Repeating System
IR
EMITTERS
POWER
15VDC
SYSTEM POWER
FROM
MODULATOR
VIDEO SYSTEM
Model 2171 IR Emitter
Compatible IR Targets
Model 2131
Model 2130A
Model 2132
With the model 3308, you can also control your video devices from any
room in the house.
Any or all 8 outputs may be connected to model
2100A wall plates. The wall plates interface with a variety of industry
standard IR targets. Direct your IR remote control at the IR target and
the 2173 IR emitter will repeat the IR signals in the media center.
IR control signals
from the bedroom …
IR control signals
from the bedroom …
Are repeated at the media
center. Change the DSS
channel or pause the
VCR from any room.
Are repeated at
the media
1
1
2
2
Normally, the IR emitters are also connected to Model 2100A wall
plates. But, if the coax panel is located in the media center, you may
choose to connect the emitters to a model 2184 IR breakout panel.
Both examples are shown below. The model 2184 plugs directly into
the 3308, replacing the power adaptor cable. The 2184 can drive up to
4 IR emitters.
If the coax panel is not located at the media center, you may add a
model 2010 remote power wall plate at the media center and connect
the 3308 and 2010 with a single coax cable. The model 2010 will power
the 3308, drive the IR emitters and deliver any modulator signals to the
3308. In addition, the 2010 has connectors for 2 IR emitters. (The
model 2174 IR expansion panel will expand each of these ports to
drive up to 4 IR emitters.)
Model 2173
Model 2173
Model 2100A
Model 2100A
Model 2100A
Model 2173
Model 2010
Model 2184
Model 2130A
Model 2132
Modulators may
be connected here.
The 2010 must be
powered as shown.
Model 2010 MUST be
connected to the ‘B’ port.
More modulators may be
connected to the ‘A’ port.
Max recommended
cable length 150’ (Total
of these two pieces.)
4
5
POWER
LED
EMITTER
LED
EMITTER
TARGET
TO
TV
TO
TV
POWER
LED
EMITTER
LED
EMITTER
TARGET
TO
TV
TO
TV
POWER
LED
EMITTER
LED
EMITTER
TARGET
TO
TV
TO
TV
IR targets must be connected
to a model 2100A wall plate.
IR targets must be connected
to a model 2100A wall plate.
DC block
When using IR repeating,
only a
or
may be directly connected
to a 3308 output.
2100A
DC block