Twin Eagles TEVH60-B - Manual (Page 2)

Page 2 of 8 11503.00 Rev C
.
NOTE: Unit must be vented
to outside of the building.
BEFORE STARTING INSTALLATION, YOU MUST IDENTIFY THE VENTILATOR MODEL BEING USED
AND IF A TOP OR REAR EXHAUST IS TO BE USED.
Prepare cabinet and/or wall for mounting either top (Fig -
3) or rear (Fig 7 & 8) exhaust. Use furring strips to level
cabinet mounting surface with any cabinet trims.
For knock out removal see Fig- B
Remove See
Ventilator Model Knock out # Transition # Fig
TEVI-060I Top Exhaust 3 TE-10100.00 1,3,4
TEVI-120I Top Exhaust 3 & 4 TE-11257.00 2,3,4
TEVE-100E &TEVE-150E 3 & 4 TE-11257.00 2,3,4
External, Top Exhaust
TEVI-060I Rear Exhaust 1 TE-11254.00 5,6,7,8
TEVI-120I Rear Exhaust 1 & 2 TE-11254.00 5,6,7,8
TEVE-100E &TEVE-150E 1 & 2 TE-11254.00 6,7,8
External, Rear Exhaust
Break the metal webs by placing a screwdriver at one
corner of the plate and hitting screwdriver sharply with a
hammer. After breaking a second web the plate can be
flexed to break other webs.
Wear eye protection when using tools.
Caution: When knock outs are removed
the edges will be sharp!!!!!!!!! Sharp Edges
should be Filed or Covered with Metal
Tape.
Attach and secure the transition to the hood with #6x3/8
sheet metal screws and tape all joints prior to installing the
hood. Attach hood to cabinet using #10 wood screws.
Holes are located in the back panel and top panel of the
hood for mounting. Use a minimum of four #10x3/4 wood
screws to mount the hood. Longer screws are required if
wall board or other nonstructural surfaces are used
between the hood and main mounting surface which
should be a minimum of 3/4” thick. When using rear holes
for additional mounting use appropriate anchors if not
engaging the wood structure.
HINT: If you find vibration noise is present because of
cabinet structure use additional screws, in holes available,
to make the mounting more ridged.
Connect 120 volt, 60 Hz power through the conduit hole
in top of hood, connecting to pigtail in hood junction box,
white to white, black to black and connect green ground
wire to the power supply ground wire per local codes. See
Fig – A.
The recommended height from countertop or cooking
surface to the bottom edge of the hood is 36 inches.
Hood is recommended for use over domestic gas or
electric appliances. Not recommended for use over solid
fuel fired appliances.
After installing the hood, install the internal blower
(Top Exhaust See Fig 1 & 2; Rear Exhaust See Fig -
5) unit by positioning the blower onto bracket-A,
notched blower bracket will center blower. Rotate
into position against hood and secure Bracket – B to
Hood with #8 sheet metal screws. If the remote
ventilator is used see related instructions. The
TEVE-150E ventilator will require revision of some
wiring in the hood receptacle box - See TEVE-150E
instructions.
NOTE: TEVE-150E requires a dedicated 20 AMP
Power Supply. All other ventilators require a
dedicated 15 AMP Power Supply
CAUTION: The hood is of sufficient weight that two
installers are recommended to prevent injury or damage to
the hood in handling.
Turn the power on at the service entrance and check the
operation of the controls.
NOTE: be sure that all dampers are operating properly and
are free to open.
BACKDRAFT DAMPER: It is recommended that a backdraft damper
(#TE-10288.00 for 8” round ducts, #TE-11257.00 for 10” round ducts) be used
in all installations. In cold weather installations it is necessary to use a backdraft
damper to minimize backflow of cold air into room. A non-metallic thermal
break should also be used to minimize conduction of outside temperatures
through the ductwork. The thermal break should be located as close as possible
to where the ducting enters the heated portion of the house. SAFTY WARNING:
Turn off power circuit at
the service entrance and
lockout panel before
wiring the range hood.