Document Outline

• Model 1000SDC 1/3 HP
• Model 2000SDC 1/2 HP
  • Start by reviewing these important safety alert symbols:
  • Mechanical
  • Electrical
• Safety Information and Precautions
  • Hardware Supplied
• Carton Inventory
• Assembly Section: Pages 6 - 7
• ASSEMBLY STEP 1
  • Fasten the Rail To the Power Unit
• ASSEMBLY STEP 2
  • instali the Trolley
• IMPORTANT INSTALLATION INSTRUCTIONS
  • Installation Section: Pages 8 - 23
  • Installation Step 1
    • Determine Header Bracket Location
      • SECTIONAL Door or ONE PIECE Door with Track
      • ONE-PIECE Door Without Track
        • Read the Safety Instructions on page 8. They also apply to doors without tracks.
        • One-piece door without track jamb hardware
        • One-piece door without track pivot hardware
        • Proceed to Step 2, page 10.
      • Fastening the Header Bracket to the Wall Fastening the Header Bracket to the Ceiling
        • Hardware Shown Actual Size
  • The Protector System®
    • Facing the door from inside the garage
  • Installation Step 4
    • Install the Safety Reversing Sensor (Receiving and Sending Eyes)
    • Installation Step 4 (Continued) Install the Safety Reversing Sensor
      • Hardware Shown Actual Size
  • Installation Step 5
    • Position the Opener
      • SECTIONAL Door or ONE-PIECE Door with Track
• A CAUTION
  • ONE-PIECE Door without Track
  • Installation Step 6
    • Hang the Opener
  • Installation Step 7
    • Install the Door Control and Connect all Wiring
• A WARNING
  • Hardware Shown Actual Size
• 9
  • Figure 3
  • Installation Step 8
    • Electrical Requirements
  • WARNING
  • /tv WARNING
    • Installation Step 9
      • Complete Safety Reversing Sensor Installation
    • Installation Step 10
      • Install the Lights and Lens
    • Installation Step 11
      • Attach the Manual Release Rope and Handle
    • Installation Step 12
      • Fasten Door Bracket
        • SECTIONAL Door Installation Procedure
          • Please read and comply with the warnings and reinforcement instructions on page 20. They apply to one-piece doors also.
    • Installation Step 13
      • Connect Door Arm to Trolley
        • SECTIONAL Doors Only
        • Figure 2
        • Hole Alignment Alternative
        • Adjustment Procedures for One-Piece Doors
    • Adjustment Step 1
      • Adjust the UP and DOWN Limits
  • A WARNING
    • How and When to Adjust the Limits
    • Adjustment Step 2
      • Adjust the Force
  • A WARNING
    • How and When to Adjust the Forces
    • Adjustment Step 3
      • Test The Protector System®
    • Adjustment Step 4
      • Test the Safety Reverse System
  • A WARNING
  • IMPORTANT SAFETY INSTRUCTIONS
  • A WARNING
  • A WARNING
    • To reduce the risk of severe injury or death to persons:
    • SAVE THESE INSTRUCTIONS
    • Care of Your Opener
• ila.' iiS)
  • Maintenance Schedule
  • Operation of Your Opener
  • A WARNING
    • Lockout position (Manual disconnect)
    • To reconnect
    • Operation of the Door Controls
    • Receiver & Remote Control Programming
      • Situation
    • Having a Problem?
      • Probable Cause & Solution
    • Having a Problem? (continued)
    • Repair Parts
      • Installation Parts
      • 11
    • Repair Parts
      • Power Unit Parts
    • Accessories Available For Your Opener
      • Model 1702LM
      • Model 60LM
      • Model 66LM
      • Model 58LM
      • Model 742LM
      • Model 64LM
      • Model 722LM
    • Index
  • 1
    • I
      • I
      • I
    • I
      • I
      • I
      • I
    • I
    • I
    • I
      • I
      • I
  • I
    • I
    • I
    • I
      • I
      • I
    • I
      • I
      • I
    • I
      • I
  • I
    • I
      • I