Carrier SYSTEM PILOT 33PILOT-01 - Manual

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
PC 111 Catalog No. 533-30017 Printed in U.S.A. Form 33ZC-4SO Pg 1 606 10-04 Replaces: New Book 1 4
Tab 11a 13a
Owner’s Manual
Part Number 33PILOT-01
CONTENTS
Page
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . 1
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Power-Up Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
OAT Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Timeout Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Program Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
• ATTACH
• CTLR-ID
• ALARM HIST
• CONFIG AND SETPOINTS TABLES
• SCHEDULE
• DETACH
Modifying Set Points
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Occupancy Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Alternate Maintenance Table . . . . . . . . . . . . . . . . . . . . . 6
Bus Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Holiday Configuration Table . . . . . . . . . . . . . . . . . . . . . . 7
SAFETY CONSIDERATIONS
Air-conditioning equipment will provide safe and reliable
service when operated within design specifications. The
equipment should be operated and serviced only by authorized
personnel who have a thorough knowledge of system opera-
tion, safety devices and emergency procedures.
Good judgement should be used in applying any manufac-
turer’s instructions to avoid injury to personnel or damage to
equipment and property.
GENERAL
The System Pilot (33PILOT-01) is a component of Carrier’s
3V™ control system and serves as the user-interface and
configuration tool for all Carrier communicating devices. The
System Pilot can be used to install and commission a 3V
zoning system, linkage compatible air source, universal
controller, and all other devices operating on the Carrier com-
municating network.
Additionally, the System Pilot can serve as a wall-mounted
temperature sensor for space temperature measurement. The
occupant can use the System Pilot to change set points and
cause occupancy overrides. A security feature is provided to
limit access of features for unauthorized users.
OPERATION
Power-Up Display — When the System Pilot is powered
up, it attaches (initiates communication) to a device that has
been designated as the System Pilot’s default device. The
System Pilot then displays that device’s custom Default screen,
if such a screen exists. If the System Pilot attaches to an
external device that does not have a custom Default screen, the
System Pilot reads that device’s first status table and displays it
as the Default screen.
DEFAULT DEVICE DESIGNATION — If the System Pi-
lot is connected to a local bus of a VVT® zone controller
(Comm2), the default device is the local zone controller. If the
System Pilot is on the Carrier communication bus, the default
device is set up by the installer.
The Local or CCN configuration is set up by the installer.
When the System Pilot is configured for Local Operation, time
and date will not be displayed on the default screens. When the
System Pilot is configured for CCN operation, the time and
date will be shown on the default screens. This way a service
person or operator may easily determine if the device may be
used to access devices on the network. The display of the con-
troller name at the top of the screen in the default display is de-
faulted to off and may be turned on by the installer also.
If the System Pilot is not connected to a local bus and no de-
fault device has been configured, the default device is the Sys-
tem Pilot itself. The default device can also be a device that has
been designated as the remote attach device. A remote attach
device is a designated Carrier network device to which the Sys-
tem Pilot will write space temperature, compute an operating
mode for, and monitor and modify set points.
All custom Default screens display the day of week, time,
and space or duct temperature. Other contents will vary
according to the attached device type. Examples of Default
screens for the System Pilot, VVT zone controller, and Bypass
Controller are shown in Fig. 1-3.
OAT Display — The System Pilot has an outside air tem-
perature (OAT) software point that can be forced from the
Carrier communicating network. If the System Pilot is display-
ing any default screen and the EXIT and SELECT buttons are
pressed together for one second, the System Pilot replaces the
default screen with a special screen that shows the OAT vari-
able value. An example of the OAT Display screen is shown in
Fig. 4. When the System Pilot is connected to the Zone Control-
ler’s local bus (Comm2), the OAT display feature is disabled.
System Pilot
Fig. 1 — System Pilot Default Screen
→