Edelbrock 14064 EnduraShine User Manual
Page 2
Part #1403, 1404, 1405, 1406, 1407, 1409, 1410, 1411, 1412 & 1413
Rev. 5/29/13- QT/mc
Page 2
©2013 Edelbrock LLC
Brochure #63-0061
POWER BRAKE PORT
(Except Marine Models)
Rear Lower Side, 1/4 NPT
IF NOT IN USE, MUST BE
PLUGGED WITH 1/4 NPT
PIPE PLUG (SUPPLIED)
MARINE FUEL PUMP VENT
(Not shown. #1409 & #1410 ONLY)
IDLE MIXTURE SCREWS
Left screw for left side of carb
Right screw for right side of carb
FUEL INLET for 3/8” hose (Except marine
models #1409 & #1410 which use a 3/8”
inverted flare fitting)
CANISTER VAPOR VENT
(#1400 Only)
IDLE SPEED
SCREW
PART NUMBER STAMPING
(Except EnduraShine™ Models)
PCV PORT
(For 3/8” Hose)
NOT FOR FUEL!
3/16” MANIFOLD VACUUM
(Distributor vacuum advance port for
non-emissions controlled engines)
3/16” TIMED VACUUM
(Distributor vacuum advance port
for emissions controlled engines)
Figure 1 - Fittings and Vacuum Port Locations
INSTALLATION PROCEDURE
BEFORE REMOVING OLD CARBURETOR
1.
Determine if the distributor vacuum port is timed (no vacuum
at idle) or full (vacuum present at idle). With the engine at
operating temperature and idling, pull the vacuum advance hose
off of the carburetor and “feel” for vacuum by putting your finger
on the vacuum port
(See Fig. 2). If
your distributor has timed vacuum
advance, you will hook the vacuum
hose from the distributor to the
passenger side vacuum port on
the new carburetor. If it has full
vacuum advance, it will be hooked
up to the driver side port.
2.
The stock steel fuel line must be modified to accommodate a
rubber fuel hose as the stock steel line will not connect directly to
the Performer Series Carburetor. The use of the Edelbrock Universal
Fuel Line Kit #8135 is highly recommended. #8135 contains a fuel
filter, rubber fuel hose, and fittings to adapt to 5/16” or 3/8” stock
steel fuel lines
(See Fig. 3). NOTE: #1405 and #1406 carburetors
are supplied with a fuel filter. If using #8135 on these carburetors,
the filter included in #8135 can be saved for later use.
WARNING: DO NOT slide the rubber fuel hose directly onto the steel
fuel line, proper fuel fittings must be used to avoid fuel leaks
. Be
sure to deburr and clean the stock steel fuel line after modification.
Fig. 3 - Fuel Line Kit #8135 Installed on Stock Steel Line
OEM Steel Fuel Line
Fuel Filter
Hose To Carburetor
Cut Stock Fuel Line and Install
fittings from Kit #8135
3.
WARNING: The use of a new fuel filter (included with #1405 and
#1406) between the fuel pump and carburetor is required. Failure
to do so will void the manufacture’s warranty of the carburetor.
4.
You must use Edelbrock Adapter #2696 or Adapter & Fuel
Line Kit #2697 when installing a Performer Series carburetor on a
General Motors Quadrajet or Chrysler Thermoquad intake manifold.
#2697 includes adapter #2696 and fuel line kit #8135.
Do not use
an open adapter (See Fig. 4).
Fig. 4
5.
You must use Edelbrock Adapter #2732 when installing a
Performer Series carburetor on certain Edelbrock intake manifolds.
In those applications, install the adapter as shown
(See Fig. 5).
Square-Bore Adapter
Plate #2732
Manifold
Gasket
Fig. 5
Fig. 2