Autostart AS-6270 - Manual (Page 4)

Once the system is set to Ready Mode, the vehicle can be remote-started and stopped at
wish.
To set the system to Ready Mode:
1. Ensure that all the doors are closed and that the shifter is in the neutral
position.
2. With the engine already running, apply the parking brake and release the brake
pedal.
Make sure to release the brake pedal.
3.
Within 20 sec. press lock , unlock or start on the transmitter.
The parking lights will flash 3 times quickly and remain lit.
4.
Remove the key: the engine will go on running.
5. Exit the vehicle and close the door.
6. Press and hold either:
a. lock to lock the doors and shut down the engine;
b. unlock to unlock the doors and shut down the engine;
c. stop to shut down the engine without affecting the doors.
Remaining In Ready Mode
Once the vehicle is in Ready Mode you can start and stop the vehicle at wish. However,
should any of the following occur, the vehicle will exit Ready Mode - thus eliminating the
remote start option until Ready Mode is restored:
1. Door opened;
2. Hood opened;
3. Brake pedal pressed;
4. Parking brake disengaged;
______ 5. Ignition key turned to the ignition on ( run ) position.____________________
Note: The unit will notify the user that it has exited Ready Mode by giving 3 slow flashes
(parking lights).________________________________________________________
Remote-starting
Press the
start button for approx. 1 second. The parking lights will come on , informing
you that the unit has received your signal. The engine will start approx. 5 seconds later.
The parking lights will remain
on during the pre-programmed run time.
If the vehicle doesn’t start at the first attempt, the system will shut down.
Vehicle Presets
Heater & Heated Seat
When leaving the vehicle it is recommended to preset the accessory controls in
preparation for the next remote start. Settings for the blower motor (fan), front and rear,
as well as heated seats (if equipped) should not be left on
high . It is recommended to
leave the settings on low or medium instead.
Windshield Wipers & Radio & Headlights
Certain vehicles require the radio and / or windshield wiper and / or headlight circuits to
become energized while running under remote start. When leaving the vehicle you must
ensure that the windshield wiper and headlight switches are
off . Leaving the headlight
switch on on certain vehicles could cause them to remain on even after remote starter
shut down, resulting in a dead battery.
P. 4 User Guide
Parking Lights Flash Rate (Normal Operation)
Flashes Description
1
♦ Doors locked, Alarm and starter kill armed.
♦ Run time has expired.
♦ TRUNK button pressed.
• Start signal received by the module.
♦ Cold weather mode cancelled.
2
• Remote start attempt cancelled by remote.
• Doors unlocked, starter kill disarmed.
• Exiting ignition valet
♦ Exiting remote valet
•
Power-up reset.
3
• Entering cold weather mode
• Entering ignition valet
• Entering or exiting Ready Mode
• Entering remote valet.
♦ Entering extended run time.
3 slow flashes^ >after a failed start attempt The module did not detect a tach signal.
4
• +12 V detected on the brake input wire
either while cranking or during run time.
• Entering multi-speed tach programming.
5 Slow ♦ Start attempt failed because no tach signal has been programmed.
5 Fast ♦ Tach signal programmed.
•
New transmitter programmed.
6 • A remote start was attempted while a tach-before-crank signal was detected before cranking.
8 • Unit reset see “Resetting the Module” (p.2)
10 • A ground (-) signal was detected on the hood pin input wire.
1 - pause - 2
♦ There was a remote start attempt while the vehicle was in valet mode.
♦ Failed start: vehicle’s low battery voltage.
2 - pause - 2 ♦ There was an attempt to start the vehicle while the module was in valet mode.
on solid for 3
seconds>.
^followed by 1 flash Exiting cold weather mode
^followed by 3 flashes Entering cold weather mode
on continuously • Idle mode: Idle mode is engaged
• Run time: The vehicle has been remote started and is in run time.
on continuously While the brake pedal is pressed. • Confirms that cold weather mode is engaged
on 2 seconds • The hood has been opened and a ground {-) signal has been detected on the hood pin input
wire.
on 4 seconds • Locking or unlocking a door (with Door pulses configured to 4 sec.)
on 20 seconds • The hood pin has been flashed and you now have access to the programming options.
on 25 sec .
• The Hood Pin-switch has been pressed twice: the Unit went into step 1 of the Programming
Centre procedure, and no Transmitter activity was detected for 20 seconds.
• Or the Unit went into step 1 of the Transmitter Programming procedure and no activity was
detected for a few seconds. The Unit has exited the Transmitter Programming procedure.
• Panic Mode is activated.
constant flashes
up to 60 sec .
• In Siren or Horn Mode: Alarm condition generated by an intrusion, or when the System is
powered up.
User Guide P. 13