Altec Lansing Duplex DTS200PIX - Manual

LANSING « DTS200PI
DTS200PIX
Duplex® Weather-Resistant
Loudspeaker Systems
• High-output capability
• Excellent directivity control
• Lightweight
• 12-inch Duplex® engine
• 90 ° X 90° Vari Intense® CD horn
• Paralleled Neutrik Speakon®
connectors
• Full-face, foam-backed grille
• Available with 100-watt trans­
former option (DTS200PIX)
Description
The Altec Lansing DTS200P1 is a two-way,
weather-resistant factory-assembled,
vented-bass. Duplex* system. This compact
system features high sensitivity, high-output
capability and point-source alignment, to­
gether with excellent directivity control
down to 1,000 Hz. The coverage at 1,000
Hz is 110° horizontal by 100° vertical, and
the system’s nominal coverage is 90° hori­
zontal by 90° vertical. The bass-reflex port­
ing extends the low-frequency response to
below 80 Hz or lower if multiple units are
used. The DTS200PI consists of a 305-mm
(12.0-inch) high-power, low-frequency
driver with a coaxially mounted 25.4-mm (1-
inch) compression driver utilizing a 90° x
90°constant-directivity hom. Electrical con­
nection to the driver is made by a parallel,
4-pin Neutrik Speakon* connector^ The sys­
tem is provided with a 1,500-Hz passive
crossover featuring tweeter protection. The
enclosure is injection molded from white
high-impact polypropylene and lined with
sound-absorbing polyester fill. Threaded 8-
mm insert mounting points are provided
to conveniently attach the Altec Lansing
MblOO, Mb200, Mb200W, Mb300W or
МЬЗОО suspension kits*. The system may
then be hung as a single unit or as part of a
cluster. The finish of the enclosure is black
textured. The grille is full-face, foam-backed,
black powder-coated metal and is fastened
to the front of the enclosure with screws.
A 100-watt transformer version (DTS200PIX)
is also available. The DTS200PIX consists
of the same components as the DTS200P1
with the addition of a 100-watts transformer
installed internally.
Architects’ And Engineers’
Specifications
The loudspeaker system shall be of the
vented-bass type, consisting of one, 305-mm
(12.0-inch) high-power. Duplex* loud­
speaker with a coaxially mounted 25.4-mm
(1-inch) compression driver loaded with a
Vari-lntense* 90° x 90° constant-directivity
hom. The loudspeaker system shall meet the
following performance criteria. Power han­
dling shall be 200 watts of pink noise with a
6-dB crest factor, band-limited from 80 Hz
to 20 kHz. Frequency response shall be
smooth and uniformly usable from 80 Hz to
20 kHz. Pressure sensitivity shall be
100 dB SPL when measured at one meter on
axis with one watt of band-limited pink noise
from 80 Hz to 20 kHz. The enclosure shall
be constructed of black, high-impact
polypropylene and shall be heavily braced
and lined with sound-absorbing polyester fill.
The finish of the enclosure shall be textured,
and a full-face, foam-backed, removable
black grille shall be provided. The dimen­
sions of the enclosure shall be
587 mm (23.1 in.) high by 429 mm (16.9 in.)
wide by 312 mm (12.3 in.) deep. The loud­
speaker system shall be: 17.3 kg (38 lb)
(nontransformer) and 21.3 kg (47 lb) (trans­
former).
The loudspeaker systems shall be the Altec
Lansing DTS200P1 (nontransformer) and
DTS200P1X (transformer).
Uniform Limited Warranty Statement
Altec Lansing products are guaranteed
against malfunction due to defects in mate­
rials or workmanship for a specified period,
as noted in the individual product-line
statement(s) below, or in the individual prod­
uct data sheet or owner’s manual, beginning
with the date of original purchase. If such
malfunction occurs during the specified pe­
riod, the product will be repaired or replaced
(at our option) without charge. The product
will be returned to the customer prepaid.
Exclusions and Limitations: The Limited
Warranty does not apply to: (a) exterior fin­
ish or appearance; (b) certain specific items
described in the individual product-line
statement(s) below, or in the individual prod­
uct data sheet or owner’s manual; (c) mal-