Argus Camera DC1512 - Manual (Page 3)

2. Press the Shutter button once within 5 seconds to delete the last photo taken.
Photo Resolution Selection
Note: The resolution status wilt always show on the LCD display in small character.
1, Press Function buuon to select Mode character show on LCD
2, “Hi" means CIF mode 352*288 Pixels, “Lo" means QCIF mode 176*1+4 pixels
3, When you select Mode function, press the shutter button once to switch between the
Hi mode or the Lo mode. The Hi mode will allow you lo take 19 photos and the Lo mode
will allow you 10 take 76 photos.
Fluorescent Lamp Frequency Selection
1. Please keep the frequency of camera in line with that of sunlight system
2. Generally speaking, there is 60Hz fluorescent lamp frequency used in United States,
Asia. And 50Hz used in Japan and Europe. If there is a wrong selection of frequency, the
photo or video shoot will have line bending.
Photo Compression Ratio Selection
There are “Hd” or “Ld* compression ratio selection for the photos stored in the memory.
The higher the compression, the more photos you can take without having to download
them to your PC. You can take up to 152 photos in the “Hd" mode when you have the
low resolution (Lo) setting preset on your camera (see the photo resolution section
above).
Photo Storage
The photo can be taken will vary referring to the resolution and compression ratio. The
LCD display will always show the status of resolution and the test of photo you may take
unless the Select Button be pressed. The highest storage of photos will be
19 photos — “Hi" resolution + "Ld" compression
76 photos — "Lo” resolution + “Ld" compression
38 photos — “Hi” resolution + “Hd" compression
-
6
-
152 photos — “Lo” resolution t “Hd” compression
Pres.s the Shutter Button to take one photo and the balance of the photos you have
remaining in the memory (based on the mode you are set in) will be displayed as a digit
on the LCD display. Each consecutive photo taken will reduce the counter by one digit.
Each time you change the resolution, the number of photos remaining to be taken will
change. If some photos were taken in a low resolution mode, then you switch to a higher
resolution, the lower resolution photos will remain in low resolution.
DownLoad Photos
When your photos memory if fully engaged, you can transmit them into the computer for
storage first. Use the included cable to connect the computer with your camera. You will
hear a single beep to indicating that the connection is correct.
1, Use USB cable to connect the computer with your camera, and the buzzer will give
out a beep sound indicating the connection is correct.
2, When you select download software "My DSCL this will open the main screen of
“My DSC”.
-7-
The function button (From left to right):
Download Photos: Download photos from your camera
Transfer Photos: Transfer photos to your album
Save: Save photos
Select all: Select all photos in the dialog box
Edit: Edit the picture
3. Press [Download photo]button .the dialog box of downloading photos will pop up.
You can download all or single photos according to your requirements.
PC Camera Functions.
Browse Live
Click (Dual-Mode (2770). and there will pop-up a dialog box below the page; click
[video camera] and the dialog box [capture the images from video camera] will
automatically pop-up. Please select (Dual mode DSC (2770)) driver for this camera,
Capture Irouge from Video Camere
Drivers:
Source j Eotmal | t,iv« | £aplut« |
Functions Introduction
I Sources-
You can set the Brightness. Contrast— device origin, device set and camera control;
and please select (Default).
2
.
Format-
You can adjust the resolution and the color mode of images; the color mode is suggest
to select [RGB-24].
3. Live-
You can browse real-time videos or images,
4. Capture-
When you play live videos, dick and select this function to acquire the single picture
and store it in the album.
5. Done-
Finish the PC Camera Functions
VideoConference
The camera can be used as a PC camera to conduct image tiaiismission or hold online
video conferences, you are only required to:
1. Use the USB cable to connect the camera and the USB interface of PC
2. Run the video conferences software Microsoft Netmeetiog on your computer,
3. Input others’ IP address in the address bar and dial
4. Select [Tool]\[Video]\[Accept] and ¡Transfer] options after others accepted yonr
calling, you can hold Video conference
-9-