Audiovox SBC Series - Manual (Page 7)

To Lock the Unit
Press IFUNCI , then key [T] (LOCK).
The ILOCKI indicator lights. The unit will remain
locked until unlocked, even if the power is turned off.
• Alert Tone: Press |RCL| , key then [§ .
Then adjust the alert tone level in the same manner
as above. Your telephone will ring at the new level.
In this case, the display format is as follows:
ALT □□ (1 to 10)
Automatic Lock (NAM Option)
If you request the feature of Automatic Lock, your
NAM can be programmed so that your unit will
automatically go into the lock mode when the power
of the unit is turned “off”. When IPWRI is turned “on”,
the unlock code is required to operate the unit.
To Unlock the Unit
Enter the three-digit unlock code. The ILOCKI indica­
tor will go out when the three-digit code is the same
as the code registered in the NAM.
Backlighting On/Off Control
LCD display and the keypad are backlit automati­
cally after the Power-On. If needed, backlighting can
be turned off by pressing
iRCLl , key |3 then .
Even if the unit is in the backlighting “Off” mode, the
backlighting will be turned on again automatically
for 10 seconds when any key operation is performed
or a call is received.
To return to the backlighting “On” mode, press
|RCL|,
key 13 then again.
Volume Control
The audio level of the loudspeaker, earpiece and the
alert tone can be adjusted by the Volume Control
key
IVOLl.
• Loudspeaker: Leave the handset on the cradle :
Keep pressing I VOL I until you get the desired sound
level.
Sound level will be displayed on the readout digitally
during the level adjustment and the sample tone will
indicate the sound level when you are not engaged in
a telephone conversation. The display format is as
follows:
SPK □□ (1 to 10)
• Handset: Lift the handset and perform the same
procedures as above.
In this case, the display format is as follows:
H.S □□ (1 to 10)
PLACING TELEPHONE
CALLS
To Place a Call
1. Enter the phone number with the handset on or off
the cradle. The last 15 digits of the dialed number
are displayed on the readout.
Note: After 120 sec., display will return to the
10-digit display mode.
2. If a dialing error is made, press |CLR| , then enter
the phone number again. Pressing |CLR| momen­
tarily (less than approx. 0.5 sec.) clears only the
last digit.
3. Press I SEND I . The I IN USE I indicator will light.
You may lift the handset either before or after the
called party answers to proceed with your conver­
sation.
Note: If assigned in NAM, the phone number can be
pre-set up to 32 digits. However, in this case
it is necessary to confirm with system opera­
tor whether such service is available or not.
If the Call Fails to Go Through
1. If you hear the “reorder” signal, press |END| , then
if there were no dialing errors, press I SEND I for
redial. (Redialing with digit keys is not necessary.)
2. If the “intercept” signal is heard, press |END| or
hang up, then redial the correct number.
Automatic Redial (NAM Option)
If the feature of Automatic Redial (NAM Option) is
selected, your unit will automatically make five
attempts to reach the cell site if the first try is not
successful. The |
IN USE] indicator will stay on, but
the speaker will be muted for twenty seconds.
This is done so that you do not hear the reorder
signals from the loudspeaker. If you need to termi­
nate the automatic redial, press fEFjPl.
Terminating a Call (Hanging Up)
Press [END I, or replace the handset on the cradle.
The I IN USE] indicator will go out.
12
13