Autostart Two-way 6-Button LCD Automatic Transmission Remote Starter User - Manual (Page 8)

Extended Run Time
While the vehicle is running under a remote start, pressing and holding the T button for more
than 3 seconds will reset the run time counter to zero and restart the run time cycle from the
beginning. There will be one beep —a pause— three more beeps; the parking lights will flash
three times and the horn (if configured) will honk once. The extended run time procedure can
only be carried out once per remote start.
To stop the vehicle, at any moment, simply press the ^ button.
Example: If your remote car starter is programmed for a run time of 3 minutes and your vehicle
has been running for 2 minutes already, pressing the ^ button will reset the counter
to zero and allow the engine to run for another cycle (in this case, 3 minutes).
Advanced Features: Installation-programmable Options
The remote starter was designed with flexibility and OEM integration in mind. With its program­
mable options, this unit can single-handedly control nearly any electrical system in your vehicle.
Caution : The programming of your system should be left to a professional. Changing any
one of the settings may affect the operation of your remote starter.
Remote Door Locks
If your remote starter was installed with the remote door locks option, you will have the
convenience of remote keyless entry. See section Arming the Starter Kill, on page 5, for further
instructions on remote door locking and unlocking.
Priority Door Access
If the remote door locks option is installed on your vehicle, this safety feature allows you unlock
solely the driver's door with a single press of the S button on the transmitter; upon a second
press of the ^ button, all the other doors will unlock.
Ignition-Controlled Door Locks
This is an added security feature. If your remote starter was installed with the ignition-controlled
door locks option, the doors will automatically be locked as soon as the ignition key is turned to the
IGNITION ON (RUN) position while the brakes are pressed. When the key is turned to the o ff position,
the doors will automatically be unlocked.
Ignition Re-lock
On remote starters of this series, when ignition-controlled door locks are enabled and the ignition
key is in the
ignition o n ( run ) position, should any door be unlocked and opened, all doors will be
relocked next time the brake pedal is pressed.
Secure Lock
Before it can remote-start your vehicle, the remote starter must first disarm the factory security
system. The secure lock feature may be required on certain vehicle models with factory security
systems that automatically unlock the doors when the security system is disarmed. To keep your
vehicle protected when the factory security system is disarmed for a remote start, secure lock will
relock your doors as soon as the vehicle has started. Once the engine run cycle ends, secure lock
will rearm your factory security system.
Remote Trunk Release
If your system was installed with the Remote Trunk Release option, you can open your trunk by
pressing the li button for 3 seconds on the remote transmitter.
P. 8 User Guide
The Starter Kill and the Anti-grind Feature
With this added security feature, the system will prevent your vehicle from starting with the ignition
key when the starter kill is armed. If your remote starter was installed with the starter kill option,
one will not be able to start your vehicle with the key unless the system has been unlocked and
disarmed first, or put into valet mode.
Note: If the starter kill is installed, your vehicle will benefit from a protection against starter
motor damage that could occur after remote-starting the engine should the user, by force of
habit, turn the ignition key to the crank position.
Separate Start and Stop buttons
The Auxiliary button 0 can be programmed as the Stop button
Safe Start Mode
If this feature is enabled, the user must press the ~ button 2 times within 3 seconds to remote­
start the vehicle. This will eliminate accidental remote starts, e.g. when children are playing with the
transmitter.
If swap start mode is selected, to remote-start your vehicle, press the iE button and then the ^
button. The Aux 2 output can be activated by pressing the
How to access Safe Start Mode
button.
Function By pressing Icon Sound Instructions / description
Start on safe start
mode
Melody
Press ^ twice within 3 seconds.
Press for 1 sec-melody-then
press 1 sec.
Stop on safe start
mode + None Melody
Installer-programmable Valet Modes
Valet Mode Using the Valet Switch (if installed)
When your vehicle is in valet mode, the remote starter functionalities are disabled. If the vehicle
needs to be serviced, or if you park it indoors, the valet mode will prevent the engine from being
remote-started accidentally.
To put the system i n t o valet mode:
1. Turn the ignition key to the ignition o n ( run ) position.
2. Within 3 sec., press the valet button (the L.E.D. will come o n solid).
3. The parking lights will flash three times to indicate that the vehicle is now in valet mode. The
L.E.D. will come o n solid.
— The CZI icon will appear on your LCD remote.
To take the system out of valet mode:
1. Turn the ignition key to the ignition o n ( run ) position.
2. Within 3 sec., press and release the valet button (the L.E.D. will come o ut ).
3. The parking lights will flash twice to indicate that the vehicle is now out of valet mode.
The L.E.D. will go out.
— The El icon will disappear from your LCD remote.
Note: Once valet mode using valet switch is activated, the remote starter will be disabled.
"Home Valet TM " Mode
If configured at installation, this feature will remotely set the vehicle to a no-remote-start mode: if
the vehicle is parked indoors there is no danger of it starting accidentally by remote control.
Note: Once the home valet mode is activated, the vehicle will not start by remote.
To take the system
• Press the ^3 or 6
n t 0 home valet mode:
i button.
User Guide P. 9