Autostart SERIAL INTERFACE DVM-2845CI - Manual

□ OEM alarm control. Make sure the module is able to arm and disarm the oem alarm (if applicable).
□ Door pin shutdown circuit. Make sure the system exits ready mode when each door is opened while the vehicle is
running under a remote start. (Test each door.)
□ Door locks and trunk testing. Make sure each of these options respond to the transmitter (if installed).
□ Starter kill option. Sit inside the vehicle with all doors closed. Arm the vehicle, then try to start the engine with the key.
The engine should not start. If the engine starts, rewire the starter kill to reach proper operation.
□ Valet mode. Make sure the remote car starter is able to properly enter and exit valet mode. When setting the remote car
starter into valet mode, pressing the lock button will lock the doors without activating the starter kill. (Refer to the user
guide for further information on valet mode.)
□ Idle mode. Make sure the vehicle properly enters and exits idle mode.
□ Most comebacks are the result of misunderstandings about how a product works or performs. Take the time to
properly explain all functions and features to the customers before they leave the premises. Doing this will save
time and money.
Diagnostics - Parking Light Flash Table
Diagnostic table for shutdown.
Parking lights flashes Cause
1 • Runtime has expired.
2
• Shutdown by remote.
• Ready mode is activated.
3 • Failed start.
4 • Brake shutdown.
10 • Hood shutdown.
Flash for 30sec • Panic mode
Diagnostic table for start failure.
Parking lights flashes Cause
1 • Ready mode is not activated.
(Manual transmission only) • Tach signal is not learned.
1 slow ^ 2 quick • The system is set to valet mode.
3 • The parking brake is active.
(Automatic transmission • Yellow loop is connected.
only)
4 • Brake wire is active
6 • A tach signal is detected before Ignition.
10 • Hood wire is active.
Note: The installer can also use the PRG-1000 to diagnose shutdown and remote start failures. Refer to the PRG-1000 manual
guide.
http://www.autostart.ca/ Installation Guide
4 - B U T T O N M A N U A L / A U T O M A T I C
T R A N S M I S S I O N R E M O T E S T A R T E R
W I T H V I R T U A L T A C H S Y S T E M
( A S P R G - 1 0 0 0 C O M P A T I B L E )
Quick Installation Guide
Internet
Explorer
To obtain a copy of the installation guide, please visit the
htto://www.autostart.ca website and click on the « Download » tab.
Table of Contents
How to Enter programming mode.................. 1
Resetting the Module..................................... 1
Manual or Automatic Transmission................ 2
Transmitter Programming Procedure............. 2
Entering Programming Options...................... 2
Programming Options..................................... 2
Bypass.............................................................3
Virtual Tach System........................................ 6
Optional Time Delay Adjustment in Virtual Tach
System.................................................. 6
How to Enter programming mode
Multi-speed Tach Programming..................... 6
Horn Honk Timing adjustment........................ 6
Supplementary Information.............................6
Fifth Relay Output (2nd IGN, ACC or CRANK)6
Tach jumper settings.............................. 7
Testing.............................................................7
Diagnostics - Parking Light Flash Table..........8
Diagnostic table for shutdown................. 8
Diagnostic table for start failure.............. 8
THE INSTALLER ^ THE MODULE ^
1) Press and hold the hood pin for 4 seconds.
2) Release the hood pin (the parking lights will turn ON).
3) While the parking lights are on, press the hood pin once more and
release immediately.
4) You now have 20 seconds to select one of the programming sub-menus.
5 ) To exit programming mode, close the HOOD.
Parking Lights "ON"
"ON" for 20 seconds
Resetting the Module
WARNING! By resetting the module, all programmed values are erased — i.e.: tach, transmitter as well as
programming options. The programming options are returned to their default values.
1. Enter programming mode (see above).
2. Once having reached the programming mode, quickly press and release the brake pedal until the parking lights flash 8
times (you will need to press the brake pedal a minimum of 5 times).
Notice
The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be that either
damage to the vehicle itself or to the unit. This unit must be installed by a certified technician using all safety devices supplied. Please
note that this guide has been written for properly trained Autostart technicians: a certain level of skills and knowledge is therefore
assumed. Please review the installation guide carefully before beginning any work.
Warning
Before installing the unit, if installing on a vehicle with a manual transmission, test that the OEM Door Switch contacts of the vehicle work
well, and that the Parking Brake system operates properly. If installing on a vehicle with an automatic transmission, test that the vehicle
does not start when the gearshift lever is in the "Drive" position. If it starts in gear, reset the remote starter to manual transmission.
Doc#: 090914 Rev:2.0 © 2009 - 1W-AM-4B-A-M - SS - Assembled in Canada
P. 8