Acoustic Image + Models - Manual (Page 7)

Warranty and Repair
We stand behind our products with a full warranty of five years from the date of
purchase. Should a problem arise, please call us before returning your
amplifier or enclosure. Naturally, our warranty does not cover products that
have been damaged through misuse. Be sure to check our web site regularly,
we have an FAQ section and we post helpful information for getting the most
out of your Acoustic Image product.
Japan version is 100V, 50/60 Hz only
Mic Input 600 ohm balanced, XLR connector,
switchable 10 dB pad
Phantom Power 47 volts, on/off switch w/LED indicator
Instrument Input 1 M impedance, 1/4 inch jack
Direct Out +4 dB, balanced, XLR connector, ground lift,
pre/post EQ selector
Effects Loop Parallel type with return level control
Bass Control Shelving type, ±15 dB at 60 Hz
Mid Control ±15 dB at 650 Hz
Treble Control Shelving type, ±15 dB at 10 kHz
Notch Filter (C1) >-18 dB sweepable from 30 to 400 Hz
Low Cut Filter (C1 & C+) -12 dB/octave sweepable from 30 to 400 Hz
Phase Reverse (C+) Switchable 180 degree phase reverse
Type Digital with 6 presets and level control
Program Presets 3 reverb (hall, room, plate), delay, ambient
chorus, flange
> W (8 > 00 W (4 ), > W (2 )
System
Power Amp (all models)
Included Accessories
Frequency Response 20 Hz - 20 kHz, ±0.5 dB
Distortion <0.5%, full output, <0.1%, typical
Hum and Noise -85 dB or better
AC Power 115V/60 Hz or 230V/50 Hz, switchable
Size 10x8x3.5 inches
Weight 4 lbs
Topology Class D (PWM)
Switching Frequency 250 kHz
Output Power-Clarus 1 >250W (8 >400 W (4 ), >500W (2 )
Output Power-Clarus+ 450 8 1000
Minimum Load 2
Output Connectors Neutrik Speakon type (pole 1)
Gig bag with shoulder strap, Speakon to
1/4 inch adapter
Preamp (Mic and Instrument Inputs through combo jack)
Effects (Clarus+)
W
W), W W
W), W W
W
Contact Information
Acoustic Image Phone: 919-785-1280
5820 Triangle Drive Fax: 919-785-1281
Raleigh, NC 27617 www.acousticimg.com
Specifications
9
FCC Compliance Notice
This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
CAUTION: Changes or modifications not expressly approved
by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of
the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiated
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and
receiver.
--Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician
for help.