Acoustic Image Ten 2 - Manual (Page 7)

10
Room Coupling Control
Description of the Ten2 EX
Care
The Room Coupling Control is also located on the rear panel of the speaker
cabinet. It is used to control the low frequency output of the downfiring woofer. It
is useful in controlling “boominess” in difficult acoustic settings. It is a three
position switch with settings of 100%, 75% and 50%. At the 100% setting, the
downfiring woofer is operating at full output. At the 75% setting, it’s output is
reduced slightly. Use this setting when there is only moderate boominess in the
room. At the 50% setting, the output is reduced even more. Use this setting for
the most difficult situations. Experiment with the control so you can get a good
idea of its effect on the sound.
The Ten2 EX is the speaker cabinet portion of the Ten2 combo. It is about 3
inches shorter and about 5 pounds lighter than the Ten2 because the docking
bay for the amplifier is not attached and the amp head is not provided. It has the
same speakers and the same performance as the Ten2. It is the ideal extension
cabinet for the Ten2 but it can also be used effectively with any of our other 1x10
combo amps. In fact, the other combos can be stacked on top of the Ten2 EX to
create a 3x10 system.
Acoustic Image combos and cabinets are made from injection molded polymer
materials. A little care will keep yours looking new for years to come. Use a
clean, dry cloth to clean the cabinet and metal parts of the amplifier.
We stand behind our products with a full warranty of five years from the date of
purchase. Should a problem arise, please call us before returning your
amplifier or enclosure. Naturally, our warranty does not cover products that
have been damaged through misuse. Be sure to check our web site regularly,
we have an FAQ section and we post helpful information for getting the most
out of your Acoustic Image product.
Warranty Information
Serial Number _______________
Acoustic Image Phone: 919-785-1280
5820 Triangle Drive Fax: 919-785-1281
Raleigh, NC 27617 www.acousticimg.com
Warranty and Repair
System
Preamp (Mic and Instrument Inputs through combo jack)
Effects
Power Amp
Speaker System
Supplied Accessories
Available Accessories
Frequency Response 30 Hz - 20 kHz (40 - 16 kHz ±3 dB)
Max SPL >116 dB at 1 meter
AC Power 115V/60 Hz or 230V/50 Hz, switchable,
Japan version is 100V, 50/60 Hz only
Size 17” H x 15” W x 13” D, 14”H (EX)
Weight 28 lbs, 23 lbs (EX)
Mic Input 600 ohm balanced, XLR connector,
switchable 10 dB pad
Phantom Power 47 volts, on/off switch w/LED indicator
Instrument Input 1 M impedance, 1/4 inch jack
Direct Out +4 dB, balanced, XLR connector, ground lift,
pre/post EQ selector
Effects Loop Parallel type with return level control
Bass Control Shelving type, ±15 dB at 60 Hz
Mid Control ±15 dB at 650 Hz
Treble Control Shelving type, ±15 dB at 10 kHz
Low Cut Filter -12 dB/octave sweepable from 30 to 400 Hz
Phase Reverse Switchable 180 degree phase reversal
Type Digital with 6 presets and level control
Program Presets 3 reverb (hall, room, plate), delay, ambient
chorus, flange
Topology Class D (PWM)
Switching Frequency 250 kHz
Output Power >450W at 8 , >800W at , >1000W at 2
External Speaker Output Neutrik Speakon type (pole 1), 2 min
load including internal speakers, if connected
Woofer Dual 10 inch, one downfiring with level
control, one forward firing
Tweeter 2.5 inch forward firing with attenuation control
Crossover Passive, alignment corrected
Impedance 4
Power rating 600W
Fitted slip cover with cord storage pocket
and shoulder strap
Padded gig bag with shoulder strap made by
Mooradian,
W
W
W
W W W
W
4
(internal speaker is 4 )
kit to convert cabinet with head
removed to an extension cabinet (adapter,
filler panel, padded case for head)
11
Specifications