Clay Paky PIPER I.C.C. - Manual (Page 2)

6
DMX 512
RS 232/423
LENS UNITS 5
BEAM OPENING m
0 5 10 15 20 DISTANCE m
0 0,80 1,60 2,40 3,20 DIAMETER m
1400 370
Objective lens 1:2,5/165mm - Standard dotation
lux 161 90
0
1
2
3
4
4
3
2
1
9
°
600 5700 232 118
2,5
0,40
7,5
1,20
12,5
2,0
17,5
2,80
HTI 150
0” 16’ 5” DISTANCE ft in 8’ 2” 24’ 7” 32’ 10” 41’ 49’ 3” 57’ 5” 65’ 7”
0” 2’ 7” 1’ 4” 3’ 11” 5’ 3” 6’ 7” 7’ 10” 9’ 2” 10’ 6” DIAMETER ft in
Objective lens 1:2,2/100mm - Available on request
0 5 10 15 20
0 1,34 2,70 4,05 5,40
500 125 lux 55 32
0
1
2
3
4
4
3
2
1
15
° 30'
2000 220 80 41
2,5
0,67
7,5
2,02
12,5
3,37
17,5
4,72
HTI 150
BEAM OPENING m
DISTANCE m
DIAMETER m
0” 16’ 5” DISTANCE ft in 8’ 2” 24’ 7” 32’ 10” 41’ 49’ 3” 57’ 5” 65’ 7”
0” 4’ 5” 8’ 10” 2’ 2” 6’ 8” DIAMETER ft in 11’ 1” 13’ 3” 15’ 6” 17’ 9”
130 34.4 fc 15.0 8.36 55.7 530 21.6 11.0
46.5 11.6 fc 5.11 2.97 186 20.4 7.43 3.81
GRAPHS SHOWING BEAM DATA AND ILLUMINATION VALUES
8
Is
PAN GOBO
COL
TILT
7 6
3 1
5
2
4
Projectors are wired up to the controller and one to the next using a multicore cable
with 8 wires of 0.25mm
2 section and a DIN 8 pin 45° plug/socket connector.
RS232/423(PMX) - DMX 512 CONNECTION
6 5
TEST 256 128 64 32 16 8 4 2 1
ON
10 9 8 7 6 5 4 3 2 1 11 12
PA
N
TIL
T
TILT
GOBO PAN
COL Is
THE DIGITAL START
ADDRESS IS THE SUM
OF THE NUMBERS
PRODUCED BY THE
SELECTED SWITCHES
DIGITAL
START
ADDRESS
AND
OPTIONS
SELECT
EG.
RESPOND
C.1 - 4
EG.
RESPOND
C.17 - 20
RUN TEST
SEQUENCE
DMX 512
RS232/423 : 1 = ,2 = SIG - ,3 = SIG +
: 1 = ,2 = SIG ,3 = SIG
DIGITAL INPUT
ANALOGUE
INPUTS 0 - 10V
• Projector address codes (for digital signals)
Each PIPER I.C.C. projector uses 1 control channel. To ensure that different projec-
tors are addressed correctly by the controller, a code must be assigned to each one.
This operation is carried out on each PIPER I.C.C. by setting the microswitches as
indicated in the table below.
Projector selection
Projectors are wired up to the controller and one to the next using two-core screened
cable and Cannon 5 pin XLR type plug/socket connectors.
To connect a DMX line, a terminating plug (5) with a 100
Ω resistor wired between pins
2 and 3 must be fitted to the last projector connected in series; the plug is not requi-
red when using an RS232/423(PMX) signal.
The wires must not come into contact with each other or with the metal casing
of the plug.
The casing of the plug/socket must be connected to the screen and to pin 1 of
the connectors.
Having completed the operations described above, press the on/off switch (6). Check
that the lamp comes on and that the auto-reset sequence starts.
SIGNAL
SCREEN
SIGNAL
5 4
3
2 1 DMX
512
SIGNAL
SCREEN
SIGNAL
RS232/423
(PMX)
1 2
3
4 5
Setting the TEST switch to the ON position for a few seconds with the projector
powered-up, an auto-reset routine is carried out. Leaving the TEST switch at the ON
position for a longer period, a full self-test program will be completed; once the ope-
ration has terminated, return the switch to the OFF position.
• Alignment procedure
Loosen the knobs (3) and
manoeuvre the projector on the
bracket (2) until the beam is
directed at centre stage and
then retighten the knobs (3).
• Adjusting the lens
Move the lens (7) back and
forward until the projected image
is satisfactorily focused, then
tighten knob (8).
POSITIONING THE PROJECTOR 3
CHANNEL FUNCTION 4
Projector 1 - Channels 1 ON
OFF
ON
OFF
TEST 128 64 32 16 8 4 2 1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
CODE
ON
OFF
Projector 2 - Channels 2
Projector 3 - Channels 3
Projector 4 - Channels 4
Projector 5 - Channels 5
Projector 6 - Channels 6
Projector 7 - Channels 7
Projector 8 - Channels 8
Projector 9 - Channels 9
Projector 10 - Channels 10
0
1
2
3
4
5
6
7
8
9
10
PINK
BLUE
ORANGE
GREEN
VIOLET
YELLOW
RED
WHITE
In the 0% to 50% range of adjustment, the
change of colour in response to the move-
ment of the potentiometer is linear and
continuous, so that the slider can be stop-
ped in intermediate positions to obtain a
two colour beam..
From 50% to 100% the wheel rotates
continuously with speed increasing
steadily from 0 to 300 rpm.
• COLOUR WHEEL - channel 1
CHANNEL
1
FUNCTION
COLOUR WHEEL
2
3 7 8