Dynavector DV XV-1s Stereo cartridge - Manual (Page 2)

 Fixing to the headshell
The thread size of the mounting holes of the XV-1 is
M2.5, so please use the enclosed screws to mount the
cartridge. Please note that the mount ing holes are 4mm
depth. Screws that are too long will damage the car tridge
body.
The cartridge should be aligned according to the arm
manufacturers instructions. They will nor mal ly supply a
protractor for this purpose.

Connection
Connect the lead wires from the headshell to each pin
shown below. Best performance is obtained if you use the
en closed lead wires that are 6N copper wire.
Please note that you should check “ Absolute Phase” to
your systems when you could not obtain a good re sult.
Because XV-1s is a very sensitive cartridge to “Ab so lute
Phase”.
 Stylus Cleaning
Keep your records clean. Dust causes record wear and
sonic distortion. When cleaning the stylus use the soft
brush supplied with the cartridge. Brush only from back
to front to avoid damage to the stylus assembly. If a dark
deposit like tan should appear on the stylus tip, always
use the soft brush with a minimum amount of high qual-
ity stylus cleaning fl uid. No-alcohol stylus cleaning fl uid is
recommended in a routine maintenance.
We do not recommend to use commercial cleaning vi-
brators.

Stylus Replacement and War ran ty
Dynavector operate an exchange scheme for the XV-1s
which entails rebuilding the car tridge. The rebuild in cludes
replacing all moving parts, ie the cantilever and stylus as-
sembly as well as the coils and sus pen sion. This al lows
re place ment stylus cost to be minimised.
To qualify for an exchange please return the cartridge to
your dealer or national distributor.
The cartridge is guaranteed for a period of one year from
date of purchase against electrical and me chan i cal defects
excluding user's mis han dling or abuse.
If there is any problem please consult your authorised
dealer fi rst for service. Should it prove necessary to return
the cartridge to the factory, you should return the defec-
tive car tridge to your dealer or national dis trib u tor, together
with the warranty card. Please keep your original packing
for safe shipping.

Specifi cations
Type : Low output moving coil cartridge with
Multi alnico magnets and Flux Damper
Output voltage : 0.3mV (at 1KHz, 5cm/sec.)
Frequency response : 20 - 20,000Hz (±1dB)
Channel separation : 30 dB (at 1KHz)
Channel balance : 1.0 dB (at 1KHz)
Compliance : 10 x 10
-6 cm/dyne
Impedance : R= 6 ohms, L= 18 micro Henry
Stylus tip : PF Line contact shape
stylus radius:7 x 30 micron
Cantilever : 6mm length 0.3mm dia. solid boron
Recommended load : more than 30 ohms
Tracking force : 1.8 - 2.2 grams
Weight : 12.6grmas
16-15 Iwamoto-cho 2-chome Chiyoda-ku
Tokyo 101-0032 Japan
Phone +81(0)3-3861-4341 FAX +81(0)3-3862-1650
http://www.dynavector.com/
This product can be recycled. Products bearing this symbol must NOT
be thrown away with normal household waste. At the end of the product's
life, take it to a collection point designated for recycling of electrical and
electronic devices. Find out more about return and collection points through
your local authority.
The European Waste Electrical and Electronic Equipment (WEEE)
Directive was implemented to dramatically reduce the amount of waste
going to landfi lls, there by reducing the environmental impact on the planet
and on human health. Please act responsibly by recycling used products. If
this product is still useable, consider giving it away or selling it.
1107120001V2