Eagle Tree OSD Pro - Manual (Page 30)

Copyright © 2009-2012 Eagle Tree Systems, LLC
http://www.eagletreesystems.com
Page 30
Issue: I am using the eLogger V3, and the Video and OSD Pro Text is visible for a while, but then the Video goes blank. If I disconnect the eLogger V3 for
a few minutes and reconnect it, the Video re-appears. I do not have any outputs from my receiver connected to the OSD Pro.
•
Solution: If you are using the eLogger V3 with the OSD Pro, make sure you are using the Battery Backup Cable as described in the “Connecting the
OSD Pro to your eLogger V3” section above.
Issue: The OSD Pro displays information on the video screen, but I cannot get the menus to appear.
Solution:
•
Ensure that you have correctly set up radio stick inputs as described in “Choosing the Radio Stick Input Method You Prefer” section of the manual
•
If you are using a switch on your radio that has a “center” position as well as “off” and “on”, make sure you are switching from “off” to “on” (or vice
versa) and are not using one of the 3 position switch radio stick input options, make sure you are not stopping at the center position of the switch.
•
Consider testing the receiver outputs that are connected to Aux1 and Aux2 with a servo, to ensure the servo moves between its extents when switching.
Issue: The OSD Pro’s GPS altitude does not zero correctly, and/or the home position does not seem correct.
Solution:
•
Adjust the “required fix quality” parameters under the GPS and Waypoints menu, to ensure that the GPS fix quality is good before the home
position is finalized.
Issue: I am seeing video “smearing” or lines on the video screen, that corresponds with the location of OSD Pro text on the screen.
Solution:
•
Adjust the OSD Pro’s “Black Level” setting, as described in the “Configure OSD Display Menu” section above.
Issue: I am having trouble adjusting the Return to Home feature.
Solution:
•
Visit our online support forum at http://www.rcgroups.com/eagle-tree-systems-443/ . There is a “sticky” post on that forum, describing how to
get help with RTH and other OSD-PRO issues.
•
If you can’t find what you need on our support forum, consider posting on our OSD Pro thread on RCGroups “First Person View” forum, at
http://www.rcgroups.com/forums/showpost.php?p=10547604 explaining the problem you are having. There are many FPV pilots there who use
the OSD Pro, and most likely some of them will have a similar setup to yours, and will be able to help you.
•
Note that Eagle Tree cannot offer email or telephone support for adjusting the Return to Home feature, due to the many variables involved.
Specifications
•
Video Modes: NTSC, PAL (automatically detected)
•
Parameters Displayed: Limited only by the sensors you have purchased
•
Character/Graphic Display Type: High contrast white with black character outline, for optimum visibility.
•
Number of Configurable Text Parameters per OSD Pro Page: 20 maximum (2 lines on top, and 2 lines on bottom, with 5 parameters on each line).
•
Mass: OSD Pro board only (no cables, eLogger or GPS): approximately 12g
Limited Warranty
Eagle Tree Systems, LLC, warrants the OSD Pro to be free from defects in materials and workmanship for a period of one (1) year from the date of original
purchase. This warranty is nontransferable. If your unit requires warranty service during this period, we will replace or repair it at our option. Shipping
cost to us is your responsibility. To obtain warranty service, email
[email protected] for further instructions.
This limited warranty does not cover:
•
The Software, including the device firmware. See the Software license agreement for more information on Software restrictions.
•
Problems that result from:
o External causes such as accident, abuse, misuse, or problems with electrical power
o Servicing not authorized by us
o Usage that is not in accordance with product instructions
o Failure to follow the product instructions
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO
STATE (OR JURISDICTION TO JURISDICTION). OUR RESPONSIBILITY FOR MALFUNCITONS AND DEFECTS IN HARDWARE IS LIMITED
TO REPAIR AND REPLACEMENT AS SET FORTH IN THIS WARRANTY STATEMENT. ALL EXPRESS AND IMPLIED WARRANTIES FOR
THE PRODUCT, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN TIME TO THE TERM OF THE LIMITED WARRANTY PERIOD AS DESCRIBED
ABOVE. NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THE LIMITED WARRANTY PERIOD HAS EXPIRED.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THIS LIMITATION MAY NOT APPLY
TO YOU.
WE DO NOT ACCEPT LIABILITY BEYOND THE REMEDIES PROVIDED FOR IN THIS LIMITED WARRANTY OR FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY LIABILTY FOR THIRD-PARTY CLAIMS AGAINST YOU FOR
DAMAGES, FOR PRODUCTS NOT BEING AVAILABLE FOR USE, OR FOR LOST DATA OR LOST SOFTWARE. OUR LIABILITY WILL BE NO
MORE THAN THE AMOUNT YOU PAID FOR THE PRODUCT THAT IS THE SUBJECT OF A CLAIM. THIS IS THE MAXIMUM AMOUNT FOR
WHICH WE ARE RESPONSIBLE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
FMA
TM , Co-Pilot TM , CPD-4 TM , Futaba TM , and Spektrum TM and all other brand and product names are trademarks of their respective holders.