Safety, Opera, Opera operation tion tion tion tion – EarthQuake WP4310 User Manual

Page 6: Burns and fires, Steps for working on engine or pump, Caution, Prep

Advertising
background image

EARTHQUAKE, Division of Ardisam, Inc.

ARDISAM

.com

.com

Page 6

800-345-6007

SAFETY

SAFETY

SAFETY

SAFETY

SAFETY

BURNS AND FIRES

BURNS AND FIRES

BURNS AND FIRES

BURNS AND FIRES

BURNS AND FIRES

The muffler, muffler guard and other parts of the engine
become extremely hot during the operation of the engine.
These parts remain extremely hot after the engine has
stopped.

This engine is designed to operate using a catalytic
converter which contributes to the engine’s compliance
with the EPA.

Prevention of Burns and Fires

Never remove the muffler guard from the engine.

Never touch the muffler guard because it is extremely

hot and will cause severe burns.

Never touch parts of the engine that become hot

during and after operation.

Always keep materials and debris away from muffler

guard and other hot parts of the engine to avoid fires.

STEPS FOR WORKING ON ENGINE OR PUMP

STEPS FOR WORKING ON ENGINE OR PUMP

STEPS FOR WORKING ON ENGINE OR PUMP

STEPS FOR WORKING ON ENGINE OR PUMP

STEPS FOR WORKING ON ENGINE OR PUMP

1. Turn off engine switch.

2. Disconnect the spark plug wire from the spark plug.

CAUTION

Avoid injury! When working on or replacing parts
for the engine or pump you must always disconnect
spark plug wire from the spark plug and keep it
away from the spark plug.

3. Securely place the disconnected spark plug wire away
from the spark plug and any metal parts. This must
always be done or arcing may occur between spark plug
wire and metal parts.

4. Replace or repair the part on the engine or pump.

5. Check all parts that were repaired, or removed during
repair, that they are secure and fit correctly.

NOTE: All repair parts must come from the factory.
Never replace parts that are not specifically designed
for the engine or pump.

6. Replace spark plug wire.

PREP

PREP

PREP

PREP

PREPARING ENGINE FOR ST

ARING ENGINE FOR ST

ARING ENGINE FOR ST

ARING ENGINE FOR ST

ARING ENGINE FOR STARTING

ARTING

ARTING

ARTING

ARTING

GAS AND OIL

Quality

To operate the engine you must use a high quality
2-cycle oil to ensure that the engine operates correctly
for the life of the engine. Use unleaded regular, unleaded
premium or reformulated automotive fuel only. It may
contain up to 10% ethanol, 10% gasohol, 15% MTBE,
and 15% ETBE. DO NOT use Methanol or leaded
fuels.

Mixture

Run earth auger with a ratio of 50:1. DO NOT use
marine 2-cycle oil.
See chart below.

CAUTION

Avoid injury! Hot gases are a normal by-product of
a functioning catalytic converter. Follow all safety
instructions to prevent burns and fires.

S

A

G

L

I

O

O

I

T

A

R

n

o

l

l

a

g

1

s

e

c

n

u

o

5

.

2

1

:

0

5

s

n

o

l

l

a

g

2

s

e

c

n

u

o

5

1

:

0

5

s

n

o

l

l

a

g

5

s

e

c

n

u

o

3

1

1

:

0

5

CAUTION

DO NOT Alter/Modify Engine or Pump:
Avoid injury! Never alter or modify the engine
from the factory. Serious injury or death may
occur if engine is modified or altered.

CAUTION

Avoid injury! Please do not start your water pump
until you have read the previous section of this
manual. Once completed, follow the steps below
to start your pump.

CAUTION

Avoid injury! Always wear hearing protection while
operating engine.

OPERA

OPERA

OPERA

OPERA

OPERATION

TION

TION

TION

TION

Advertising