GlowShift Oil Pressure Gauge - Manual (Page 2)

Operating Instructions
1. 10-Color Mode:
1. Press the COLOR button to cycle between the 10 different color options.
2. The sequence of display colors are: Blue, Green, Red, Yellow, White, Light Blue, Purple, Pink, Orange, Amber. After Amber there are 2
automatic color changing functions on the gauge that begin with the color Blue. They are the 10 Color Cycle Mode and the 10 Color
Slow Fade Mode.
2. Setting the Peak Recall:
1. Press the SET button on the front of the gauge to recall your last peak value and enter into the peak setting mode. The word PEAK will
turn blue when you are in the peak recall setting mode
2. Once the peak value is displayed, press the COLOR button to clear the previous peak value. When the Peak Blue LED is not flashing,
the gauge is operating in normal mode.
3. Setting the High-Warning Mode:
1. Press and hold the COLOR button for 5 seconds to enter the High-warning setting mode.
2. When the needle is flashing and the warning light is on, you can now program the High-Warning Mode Value. Pressing the COLOR
button will move the needle clockwise while pressing the SET button will move the needle counter-clockwise.
3. Holding either the COLOR button or the SET button will move the needle in major increments in the buttons respective direction.
4. After 5 seconds of no button activity, the gauge will return to its normal operating mode.
5. To turn the warning sound on for this mode, turn the gauge off. While holding the COLOR button, turn on the gauge until you hear a
single beeping sound. Repeat to turn off.
4. Low-Warning Mode:
1. Hold the SET button for 5 seconds to enter into the Low-warning setting mode.
2. When the needle and warning light are flashing, you can now program the Low-Warning Mode Value. Pressing the COLOR button will
move the needle clockwise while pressing the SET button will move the needle counter-clockwise.
3. Holding either the COLOR button or the SET button will move the needle in major increments in the buttons respective direction.
4. After 5 seconds of no button activity, the gauge will return to its normal operating mode.
5. To turn the warning sound on for this mode, turn the gauge off. While holding the SET button, turn on the gauge until you hear a single
beeping sound. Repeat to turn off.
5. Key Sound Mode:
1. To hear the key sound when either button is pressed, turn the gauge off.
2. Hold the COLOR and SET buttons at the same time and then turn on the gauge until you hear two beeping sounds. The Key Sound
Mode is now activated.
3. Holding the COLOR and SET buttons at the same time and then turning off the gauge will deactivate this setting.
Additional Installation Information & Material Requirements

GlowShift Gauges Approved Conductor Wires: Successfully installing GlowShift Gauges may require lengths of wire (sizes and quantity
depend on vehicle, gauge type, gauge location and / or sensor location). For correct and proper GlowShift Gauge installation and operation, the
use of 18 Gauge (wire diameter) automotive grade conductor wire with sheathing is recommended for one or more gauges per vehicle. When
installing and routing wires from the engine compartment, to inside the vehicle cabin, always employ the use of a rubber grommet. This will
prevent and deter the stripping of power supply and / or sensor wires that is necessary to deliver vital statistics about your engine to your
GlowShift engine monitoring instruments. Never use wire nuts to fasten or bound vehicle / gauge or sensor wiring. Always use securing crimp
connectors or solder individual wire junctions together for optimum gauge installation and operation.

GlowShift Gauges Approved Installation Accessories: GlowShift Gauges may require the installer or user to provide additional products,
accessories or adapters for the correct installation and operation of a gauge or sensor, as per the GlowShift Installation Instructions. When
installing and routing hoses to or from the engine compartment, to inside the vehicle cabin, always employ the use of a rubber grommet. This
will prevent and deter the stretching or pinching of hoses that is necessary to deliver vital statistics about your engine to your GlowShift engine
monitoring instruments.

GlowShift Gauges Installation Instructions: Installation documents are solely to provide a guide for individuals that are mechanically and
electronically able to install products. If you are unsure about the correct procedure of installation for a product or device, you should consult a
professional mechanic or an Authorized GlowShift Installer.