HITEC FunCub - Manual (Page 8)

14
Parts List - FunCub
Part No. Description Material Dimensions
No. off
1 1 Building instructions
2 1 Decal sheet 500 x 880 mm
3 1 L.H. fuselage shell Moulded Elapor foam Ready made
4 1 R.H. fuselage shell Moulded Elapor foam Ready made
5 1 Canopy Moulded Elapor foam Ready made
6 1 L.H. wing panel Moulded Elapor foam Ready made
7 1 R.H. wing panel Moulded Elapor foam Ready made
8 1 Tailplane Moulded Elapor foam Ready made
9 1 Fin Moulded Elapor foam Ready made
70 1 Main undercarriage unit Spring steel, 2.5 Ø Ready made
71 2 Lightweight wheel Plastic, EPP 120 Ø, hub bore 2.6 mm
Small parts set, motor mount
20
3 Velcro tape, hook 25 x 60 mm
21 3 Velcro tape, loop 25 x 60 mm
22 2 Latch catch Inj.-moulded plastic Ready made
23 2 Latch tongue Inj.-moulded plastic Ready made
24 1 Glue-fitting horn Inj.-moulded plastic Ready made
25 4 Swivel pushrod connector Metal Ready made, 6 mm Ø
26 4 Washer Metal M2
27 4 Nut Metal M2
28 6 Socket-head grubscrew Metal M3 x 3 mm
29 1 Allen key Metal 1.5 mm A/F
30 1 Front spar joiner, “deep” Inj.-moulded plastic Ready made
31 1 Rear spar joiner, “shallow” Inj.-moulded plastic Ready made
32 2 Screw Plastic M5 x 50 mm
33 2 Wing spreader plate A Inj.-moulded plastic Ready made, M5
34 2 Wing spreader plate B Inj.-moulded plastic Ready made, M5
35 1 Glue-fitting horn, tailskid Inj.-moulded plastic Ready made
36 1 Glue-fitting tailwheel bracket Inj.-moulded plastic Ready made
37 2 Motor mount Inj.-moulded plastic Ready made
38 1 Motor bulkhead Inj.-moulded plastic Ready made
39 4 Motor bulkhead adjustment screw Metal M3 x 10 mm
40 2 Motor bulkhead mounting screw Metal M3 x 16 mm
41 8 “Twin” control surface horn Plastic Ready made
42 6 “Twin” horn bracket Plastic Ready made
43 2 Pivot barrel Metal Ready made, 6 mm Ø
44 2 Glue-fitting horn, landing flaps Inj.-moulded plastic Ready made
45 2 Pre-formed aileron pushrod (Z-bend) Metal 1 Ø x 90 mm
46 2 Pre-formed flap pushrod (Z-bend) Metal 1 Ø x 105 mm
47 1 Aero-tow mechanism Inj.-moulded plastic Ready made
48 1 Aero-tow release pushrod (Z-bend) Metal 1 Ø x 90 mm
Wire and rod set
50
2 Front tubular spar CRP tube 8 Ø x 6 x 400 mm
51 2 Rear tubular spar CRP tube 8 Ø x 6 x 100mm
52 1 Elevator pushrod (Z-bend) Metal 0.8 Ø x 510 mm
53 1 Rudder pushrod (Z-bend) Metal 0.8 Ø x 510 mm
54 1 Elevator snake outer sleeve Plastic 3/2 Ø x 480 mm
55 1 Rudder snake outer sleeve Plastic 3/2 Ø x 480 mm
56 1 Elevator snake inner sleeve Plastic 2/1 Ø x 500 mm
57 1 Rudder snake inner sleeve Plastic 2/1 Ø x 500 mm
Undercarriage set
72
4 Collet Metal 2.7 Ø / 8 x 5 mm
73 4 Socket-head grubscrew Metal M3 x 3 mm
74 1 Undercarriage bracket Plastic Ready made
75 1 Screw Metal M3 x 12 mm
76 1 Tailwheel unit Metal 1.3 mm Ø
77 1 Lightweight tailwheel Plastic, EPP 53 Ø, hub bore 1.6 mm
78 2 Tailwheel retainer (tubular rivet) Metal rivet 2.0 Ø x 0.2 x 3 mm