Imaxrc IR-GT3B - Manual (Page 13)

EXP:
LCD Functin Explantion
22
LCD Functin Explantion
23
Function explanation:
This function is used to change the sensitivity of steering servo’s 3
channels around the neutral position. In order to soften the response
according to user’s demand.
Parameter specification:
CHANNEL: channel number, from 1 to 3;
100%:steering EXP rate, when you want aggressive steering operation,
turn the button to increase the rate. When you want to make steering
operation less aggressive, turn the button to decrease the rate.
Adjustment range : -100%~0~+100%(initial value is 0)
Operation:
Press the ENTER button and turn select the EXP option. The selected
function will be blinking. Select the channel by turning the ENTER button.
And then press the END button(now the percentage will be blinking).
Turn the ENTER button to adjust the rate. After this, press the END button
to finish the setting. The rest can be done in the same way. After finishing
the setting of three channels. Press the ENTER button to return to menu
screen.
Press BACK to return to the opening screen.
Ҫᑟឭ௚Ὁ
൥Ҫᑟ௧ࠫʼ˔ᣥѣᤰ᥋Ϣᣥѣԫӑ᧚ូட᝺ࠀἻ൥ᮊ᝺ࠀՏ௑ࠫːᦊѬἷ൤ӧᦊѬ᠇
ӧᦊѬἸોՏʷඋဋᤉᛡ᝺ࠀἻᤠऄˀՏ᭧መԣˀՏͪ఩٨ᣥѣᄊ᜶රἻ̿᣺҂తΈᄊ
୲଍஍౧Ǎ
Ԡ஝ឭ௚Ὁ
CHANNEL: ᤰ᥋ᎄՂἻᤰ᥋1҂ᤰ᥋3
100%: ᣥѣ᧚ᄈѬඋဋἻϙᡕ࠵ᣥѣᡕ࠵ἻԦ˨ᡕܸἷ൥ូட᧚˞0%҂100%ἻࢺԈᮕ᝺
ϙὉ˞100%ἸἻ 0%᛫ᇨ൥ᤰ᥋෥దᣥѣἻ100%᛫ᇨЛᦊᣥѣἻ˷ࡃ௧తܸᣥѣǍ
୲ͻவขὉ
ښन఻ᖝӭʾᤰ᣿ᆸᝣ᪄ᤉКᖝӭἻᤰ᣿ࢻԿ஽ᣁ᪄ᤉᛡ%3ᖝӭᤥહἻгોᆸᝣ᪄᜶
ԫఞᄊᤰ᥋Ցો&/%᪄Ἳ൥௑ʼ˔ߚኀ᫅͘ཇἻښ൥࿄গʾોࢻԿ஽ᣁ᪄
ᤉᛡ
ᤉК൥ᖝӭᄊ୲ͻἷ൥௑ߚኀ᫅͘ཇἸἻཀྵՑᤰ᣿ࢻԿ஽ᣁ᪄ᤉᛡᤰ᥋҂ᤰ᥋ᄊᤥ
હἻᤥݞᄊ᝺ࠀǍ߹ੇՑો&/%᪄ԻᤉКԳʷ˔ᤰ᥋ᄊ᝺ࠀǍΚዝ଎ࠫʼ˔ᤰ᥋ᤉᛡ᝺
ࠀǍ
ᎄᣤ߹ੇՑોᆸᝣ᪄ᤅڀࣳᤉКᖝӭᤥહ࿄গǍ
ښ͊͵࿄গʾોᤅڀ᪄
ᤉКन఻ႇ᭧Ǎ
Ҫᑟឭ௚Ὁ
൥Ҫᑟ௧ࠫʼ˔ᣥѣᤰ᥋Ϣᣥѣԫӑ᧚ូட᝺ࠀἻᤠऄˀՏᠿ᥋ԣˀՏ̡ᄊ୲ͻ˸ਅἻ
̿᣺҂తΈᄊ୲଍஍౧Ǎ
Ԡ஝ឭ௚Ὁ
CHANNEL: ᤰ᥋ᎄՂἻᤰ᥋1҂ᤰ᥋3
100%: ᣥѣ᧚ᄈѬඋဋἻ-100%᛫ᇨ˗ॷགͯᎶԦऄ͘ᡕ࠵Ἳ˷ࡃ௧Ԧऄᡕᤍ᧽Ὂ100%
᛫ᇨ˗ॷགͯᎶԦऄ͘ᡕܸἻ˷ࡃ௧Ԧऄᡕ༧ஐἻEXPូட᧚˞Ὁ-100%҂100%ἷࢺԈᮕ
᝺ϙ˞0%ἸǍ
Parameter specification:
CHANNEL: channel number, from 1 to 3;
100%: Dual Rate, when you want to increase the servo travel, turn the
button to increase the rate. When you want to decrease the servo travel,
turn the button to decrease the rate. 0% is no signal output, 100% is
maximum signal output. Adjustment range: 0~100%(initial value is 100%)
Operation:
Press the ENTER button and turn to select the D/R option. The selected
function will be blinking. Select the channel by turning the ENTER button,
and then press the END . After this, press the END button to finish the
setting. The rest can be done in the same way. After finishing the setting
of three channels, press the ENTER button to return to menu screen.
Press BACK to return to the opening screen.
Automatic Frequency Hopping Digital System ghz ghz ghz 01010101 01010101 01010101
DIGITAL PROPOTIONAL RADIO CONTROL SYSTEM
MULTI-DATA COMPUTERIZED DISPLAY
3CHANNEL
10MODEL
CAR/BOAT