Laerdal SimNewB Advanced - Manual

SimNewB Installation Guide SimNewB™ Advanced system - Installation Guide
CHECK EQUIPMENT
USB Hub box
with Powersupply
and USB cable
USB Camera box
SimNewB Advanced accessories
- Audio cable, 3-way
(Images below are examples only. Actual components may vary.)
© 2008 Laerdal Medical AS All Rights reserved XXXX rev X
Computer with accessories:
- Powersupply with cable
- USB mouse
Monitor with accessories:
- Video cable
- Powersupply with cable
- USB cable
START YOUR COMPUTER
INSTALL THE USB HUB
I GET TO KNOW THE SUPPORT MATERIALS
Software for Windows® XP and Windows® Vista
XXXXX rev X Ver 1.x
Scenario Builder Log and Scenario Control USB Drivers
SimNewB™
??
- SimNewB Installation Guide
- SimNewB DFU
- SimNewB Helpfiles
Connect the mouse and power supply to the computer, and turn on.
Make sure that your computer has the SimNewB logo on the screen.
A USB hub is provided with the system to overcome
potential problems of having too few USB ports on the
computer and to have fewer cables from the computer
in the manikin area.
- Unpack the USB Hub from its box
- Connect power to the USB Hub
- Connect the USB Hub to the PC
CONNECT THE MONITOR CABLES TO THE COMPUTER
- Connect the Video cable to the Computer.
- Connect the Audio cable to the Computer headphone
output - phono jack with double wire.
- Do NOT connect the USB cable yet.
CONNECT THE PATIENT MONITOR
- Unpack the Patient Monitor and cables.
- Do
NOT use the Software CD that comes with the monitor.
- Route the cables through the Monitor Stand
and connect the cables to the monitor connectors:
(refer to accompanying R10
(??) documents for details)
• Video cable.
• USB cable.
• Audio cable - mini jack with single wire.
• Power cable.
- Secure the cables using the strain
reliefs on the monitor.
- Connect the power cable between
the power supply and a wall outlet,
and turn the monitor on.
CONNECT THE MANIKIN TO THE CONTROL UNIT
- Unpack the SimNewB manikin and cables.
- With the 25 feet long extension cable, connect the Manikin cable and
blood pressure tube to the Control Unit.
CALIBRATE THE TOUCH SCREEN MONITOR
- Double click on the elo logo in the system tray
in the lower right corner of the screen.
(If you cannot find it in the system tray, activate
Elo Touchscreen in the Control Panel).
- Click on the Align button on the dialog that appears.
- If target indicators first appear
on the computer screen, press Esc,
or wait until they appear on
the Patient Monitor.
- When the target appears on the Patient Monitor, touch each target as
it changes position, and finally touch the green tic button.
You are now ready to start using your SimNewB Advanced system
INSTALL THE COMPRESSOR OR REGULATOR UNIT
- Unpack the compressor with power cable.
Connect the power cable to the compressor and a wall outlet.
- Unpack the compressor air tube and connect it between
the manikin and the compressor.
- Operate the unit according t o accompanying instructions.
CONNECT THE BLOOD PRESSURE CUFF
TO THE MANIKIN
- Unpack the BP cuff and connect to the
blood preesure tube on the manikin cable bundle.
1 4 3
INSTALL THE MONITOR ON THE COMPUTER
- Right click on the Desktop and select Properties.
- Select the Settings tab.
• Select Display 2.
• Set Resolution to 1280 x 1024 pixels.
• Check Extend my Windows desktop
onto this monitor.
• Click OK.
• If promted: Answere Yes to keep
this setting.
2
During installation: Make sure you accept the default settings and/or unblock, unless
other instructions are given in the Installation Guide and other instruction material.
INSTALL THE CONTROL UNIT
- Connect the USB cable between the Control Unit and the USB hub
- Connect the Audio cable - mini jack with single wire (color code?) to
the Control Unit.
- Connect the Control Unit’s power supply between a wall outlet and
the Control Unit, and turn the Control Unit on.
INSTALL THE WEB-CAMERA
- Unpack the web-camera
- Connect the web-camera to the USB-hub.
A. Setup of SimNewB Advanced system elements
CONNECT CO 2 TO THE COMPRESSOR...
- Attach regulator to the CO 2 bottle
- Attach the black tube between the regulator and the Compressor
Unit or Regulator Unit’s CO
2 inlet connector.
CONNECT THE MONITOR TO THE USB HUB
- Connect the Patient Monitor to the USB hub.
1
2
II CHECK THAT ALL ITEMS ARE PRESENT
3
4
5
6
7
8
9
Power
Power
Power
P o w
e r
B. Setup of the SimNewB manikin system and compressor
10
11
CONNECT THE IV BAG RESERVOIR
12
14
SimNewB™ manikin setup
Power
Power
- Connect the IV bag reservoir to the Manikin’s overflow tube.
13
C O
2 ta n k
Video cable
Audio cable
USB Hub
To power
adapter
To PC’s
USB port
USB cable
Audio cable
To power
adapter
Extension cable:
Manikin cable and
blood-pressure tube
BP cuff
connector
IV Bag reservoir
connector
CO 2 regulator
CO 2 tube
If your SimNewB purchase included a laptop supplied by Laerdal
follow the instructions on page 2-4.
Compact Compressor with accessories:
- Powercable
- Regulator
- CO
2 tube
SimNewB manikin with accessories:
- Control Unit
- Powersupply
- USB cable
- Manikin cable, 25 ft.
- Air/CO
2 tube
- IV bag reservoir
- Blood pressure cuff
SimNewB Advanced system elements
SimNewB manikin system - elements required for setup
Alternatively, a Laerdal Regulator Unit
may be used.
Monitor
USB Webcamera