Paradigm PT-2 Wireless Transmitter - Manual (Page 2)

-
- - -
-
-
-
+
+
+
+
-
-
+
+
+
+
-
-
- - -
-
+
+
-
-
+
+
-
-
-
+
+
+
+
-
- -
-
-
-
+
+
+
+
-
-
+
+
+
+
-
- -
+
+
-
+
+
-
-
-
-
RECYCLING AND REUSE GUIDELINES FOR EUROPE
In accordance with the European Union WEEE (Waste Electrical and Electronic
Equipment) directive effective August 13, 2005, we would like to notify you that
this product may contain regulated materials which, upon disposal, according
to the WEEE directive, require special reuse and recycling processing. For this
reason Paradigm Electronics Inc. (manufacturers of Paradigm speakers and
Anthem electronics) has arranged with our distributors in European Union
member nations to collect and recycle this product at no cost to you. To find
your local distributor please contact the dealer from whom you purchased this
product or go to our website at www.paradigm.com.
Please note that the product only falls under the WEEE directive. When
disposing of packaging and other shipping material we encourage you to
recycle through the normal channels.
This device contains FCC ID: YZY-HT205 and IC ID: 9261A-HT205. This device
complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including interference that
may cause undesired operation.
ABOUT YOUR PT-2 TRANSMITTER PANEL LAYOUTS WIRELESS SYNC INSTRUCTIONS
LATENCY SWITCH INSTRUCTIONS
+ +
+
-
-
-
-
-
+
+
B A
LED STATUS
Wireless
Subwoofer
Receiver
Receiver
Wireless
Subwoofer
Receiver
Wireless
Subwoofer
Paradigm VC-150
Volume Control
SPEAKER-LEVEL CONNECTION,
VOLUME CONTROLLED BY RECEIVER
LINE-LEVEL CONNECTION (NO SUB-OUT/LFE):
VOLUME CONTROLLED BY RECEIVER SPEAKER-LEVEL CONNECTION:
VOLUME CONTROLLED EXTERNALLY (ZONE 2)
Zone 2 volume level of full-range speakers and subwoofer may be controlled
by the Paradigm VC-150 Volume Control
(sold separately). Requires running
speaker wire from the Paradigm VC-150 Volume Control back to the
Paradigm PT-2 transmitter.
1. Plug in PT-2 wireless transmitter.
2. Press and hold sync button on front panel of PT-2 for
3 seconds. The LED will blink quickly.
3. Within 60 secs of pressing the sync button all subwoofers
must be plugged in. Once all subwoofers are synched, the
LED will remain ‘on’.
Off: No power.
Fast blinking: Set-up mode.
Dim: Unit in standby mode, no transmission.
Slow blinking, ‘off’ to bright: Waking from standby mode
and synching.
Slow blinking, dim to bright: At least one subwoofer is synched.
Permanently On: All subwoofers synched and receiving signal.
B
A
TIP! Once all subwoofers have been synched, if necessary they
can be unplugged and moved without resynching again.
The latency switch adjusts the delay between the PT-2’s audio
signal input and the subwoofer receiver’s RF output, optimizing
integrity of the wireless transmission. Start with the switch
in the 15ms position. If you experience sound quality issues
(i.e drop-outs, pops, ticks), you can improve the connection by
moving the switch to 20ms or 25ms to increase latency.
Receiver without line-level connection. Receiver without bass management.
-
- - -
-
+
+
-
-
+
+
-
-
-
+
+
+
+
/Sub-In
Sub-Out
Receiver
Wireless
Subwoofer
LINE-LEVEL CONNECTION (WITH SUB-OUT/LFE):
VOLUME CONTROLLED BY RECEIVER
Receiver with bass management.
Volume Control occurs at receiver.
In a typical listening room the PT-2 transmitter has a
maximum range of 50’ (15 m). Obstructions such as walls,
large pieces of furniture, room dividers, etc., may reduce this
range. Do not place subwoofer(s) and transmitter farther
apart than the recommended range. The PT-2 is a 2.4 GHz
digital design that automatically adjusts for best wireless
connection while constantly monitoring the integrity of the
data stream. An RCA audio cable is required (not included) to
connect it to your A/V receiver or preamplifier (see dealer).
One PT-2 transmitter can be used with up to four wireless
Paradigm subwoofers. See dealer for full details on connecting
multiple subwoofers.
Zone 2 Operation
Your PT-2 transmitter will work with a subwoofer(s) in a second
zone (i.e. another area of your home).
TIP! To minimize the chance of signal dropouts or signal
interference, keep the PT-2 transmitter out of range of a
microwave oven, mobile telephone or a Bluetooth device
operating on the same frequency.
IMPORTANT! Paradigm recommends using
speaker-level OR line-level connections. DO
NOT USE BOTH CONNECTIONS AT THE
SAME TIME.
Your PT-2 transmitter is designed to work
with Paradigm brand subwoofers only.
C
C
All subwoofers must be unplugged from outlets.