Peg-Perego Case IH Lil Tractor - Manual (Page 8)

CAUTION:
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS COMPONENTS TO BE ASSEMBLED MAY POSE A SMALL PARTS/SHARP EDGE
HAZARD.
BATTERY IS INCLUDED AND MUST BE CONNECTED;
1 • Unscrew the 2 knobs under the seat.
2 • Position the seat as shown in the figure.
3 • IMPORTANT: the seat can be adjusted to 2 positions depending on the height of the child (see figure). Position 1: the seat is higher and further back. Position
2: the seat is lower and further forward.
4 • Turn the vehicle on its side, keeping the seat in position. Remove the screw from the access door, under the vehicle.
5 • Open the cover to access the seat attachment knobs.
6 • Screw on the two seat knobs as shown in the figure. Close and screw on the cover.
7 • Snap on the 2 rear light lenses.
8 • Assemble the indicators as shown in the figure.
9 • Attach the 2 indicators at the front of the vehicle, as shown in figures 1-2, taking care that the hollow part of the indicator is facing down.
10 • Press on the 2 headlight lenses as shown in detail A.
11 • Position the steering wheel. Attach the steering wheel with the screw (10P x 1
1/4 inch) and washer (5 x 11 x 1 mm) provided.
12 • Push on the steering wheel cap as shown in the figure.
13 • Insert one of the 4 self-locking washers (the tractor comes with 2 spare washers) into the special tool provided with the tractor. ATTENTION: the tabs on the
self-locking washer must be turned towards the interior of the tool (see detail A).
14 • Remove the axle from the packing. Remove the protective caps from the axle. Insert the axle by pounding the special tool all the way in using a hammer.
Remove the tool.
15 • Slide the 2 wheels onto the axle. IMPORTANT: check that the wheels are correctly inserted, with the hub caps facing out.
16 • Place a self-locking washer in the special tool, and insert the prepared axle, pounding it all the way in.
17 • Attach the wheel unit to the base of the trailer by pressing on it.
18 • Attach the bottom of the trailer (prepared beforehand) to the bed by pressing, as shown in the figure.
19 • Assemble the 3 sides of the trailer, ensuring that the parts with the wooden effect are facing outwards.
20 • Fit the assembled parts into the slots in the base of the trailer.
21 • Insert the red coupling into the hole on the trailer (see figure).
22 • Couple the trailer onto the back of the tractor, rotating the red lever. Figure 1: the trailer can be uncoupled; figure 2: the trailer coupled. WARNING: The
trailer will hold a load weighing up to 11 lbs (5 kg).
23 • Attach the 2 hubcaps to the wheels on the trailer (Attention, in the packaging you will find 6 hubcaps; the remaining 4 are to be attached to the wheels of the
tractor).
24 • Unscrew the hood.
25 • Pull the hood towards you while lifting and turning it to remove (see figure).
26 • Connect the battery plug to the electric system plug.
27 • Close the hood, taking care to correctly insert the tabs into the openings in the chassis. ATTENTION: Detail A shows the hood incorrectly attached. The
vehicle is ready for use.
VEHICLE FEATURES AND INSTRUCTIONS FOR USE
28 • ACCELERATOR PEDAL/ELECTRIC BRAKE: when the foot is lifted from the accelerator pedal, the electric brake automatically stops the tractor.
BATTERY REPLACEMENT
WARNING:
WARNING: BATTERY CHARGING AND ANY OTHER OPERATION ON THE ELECTRICAL SYSTEM MUST BE
CARRIED OUT BY ADULTS ONLY.
THE BATTERY CAN ALSO BE CHARGED WITHOUT REMOVING IT FROM THE VEHICLE.
29 • Unscrew the hood.
30 • Pull the hood towards you while lifting and turning it to remove (see figure).
31 • Loosen the 2 screws that hold the battery in place.
32 • Disconnect the 2 plugs and remove the battery supplied with the vehicle.
33 • Insert a new battery and connect the two plugs.
34 • Screw the battery clamp into place again, turning it upside down as shown in the figure. Close the hood as described above (fig. 27) and fasten with the screw.
BATTERY RECHARGE
35 • Unplug vehicle wiring terminal A from battery terminal B, by pressing terminals on side and pulling apart.
36 • Plug the battery charger terminal to a wall outlet following the instructions enclosed. Connect the plug B to the battery charger plug C.
37 • Once the charge is completed unplug recharger from wall outlet. Unplug recharger cord terminal C from battery terminal B.
38 • Plug battery terminal A into vehicle wiring terminal B. Close hood.
ASSEMBLY INSTRUCTIONS
INITIAL BATTERY CHARGE
!• Remove battery and charger from packaging. Connect battery charger to a 120vac wall recepticle. Connect battery charger to battery.