Rigel Systems Skylite Mini - Manual

Mini LED Light
Operation: Push thumbwheel forward to light,
on two color modles, toggle switch left /right to
select LED color
Low battery Indication: White LEDs don't light,
Red LEDs light dimly. This is normal as white
LEDs require higher voltage.
How to change the battery:
1) Depress latch tab by pressing bump next to
thumbwheel, rotate cap out and down to
remove.
2) Remove circuit board and battery.
3) Detach battery from circuit board and attach
new 9 volt.
4) Insert circuit board and battery into body.
5) Insert hinge tab into hinge hole (see picture
below) and pivot cap upward around hinge
until latched.
Mini LED Light
Operation: Push thumbwheel forward to light,
on two color modles, toggle switch left /right to
select LED color
Low battery Indication: White LEDs don't light,
Red LEDs light dimly. This is normal as white
LEDs require higher voltage.
How to change the battery:
1) Depress latch tab by pressing bump next to
thumbwheel, rotate cap out and down to
remove.
2) Remove circuit board and battery.
3) Detach battery from circuit board and attach
new 9 volt.
4) Insert circuit board and battery into body.
5) Insert hinge tab into hinge hole (see picture
below) and pivot cap upward around hinge
until latched.
Mini LED Light
Operation: Push thumbwheel forward to light,
on two color modles, toggle switch left /right to
select LED color
Low battery Indication: White LEDs don't light,
Red LEDs light dimly. This is normal as white
LEDs require higher voltage.
How to change the battery:
1) Depress latch tab by pressing bump next to
thumbwheel, rotate cap out and down to
remove.
2) Remove circuit board and battery.
3) Detach battery from circuit board and attach
new 9 volt.
4) Insert circuit board and battery into body.
5) Insert hinge tab into hinge hole (see picture
below) and pivot cap upward around hinge
until latched.
Mini LED Light
Operation: Push thumbwheel forward to light,
on two color modles, toggle switch left /right to
select LED color
Low battery Indication: White LEDs don't light,
Red LEDs light dimly. This is normal as white
LEDs require higher voltage.
How to change the battery:
1) Depress latch tab by pressing bump next to
thumbwheel, rotate cap out and down to
remove.
2) Remove circuit board and battery.
3) Detach battery from circuit board and attach
new 9 volt.
4) Insert circuit board and battery into body.
5) Insert hinge tab into hinge hole (see picture
below) and pivot cap upward around hinge
until latched.
Mini LED Light
Operation: Push thumbwheel forward to light,
on two color modles, toggle switch left /right to
select LED color
Low battery Indication: White LEDs don't light,
Red LEDs light dimly. This is normal as white
LEDs require higher voltage.
How to change the battery:
1) Depress latch tab by pressing bump next to
thumbwheel, rotate cap out and down to
remove.
2) Remove circuit board and battery.
3) Detach battery from circuit board and attach
new 9 volt.
4) Insert circuit board and battery into body.
5) Insert hinge tab into hinge hole (see picture
below) and pivot cap upward around hinge
until latched.
Mini LED Light
Operation: Push thumbwheel forward to light,
on two color modles, toggle switch left /right to
select LED color
Low battery Indication: White LEDs don't light,
Red LEDs light dimly. This is normal as white
LEDs require higher voltage.
How to change the battery:
1) Depress latch tab by pressing bump next to
thumbwheel, rotate cap out and down to
remove.
2) Remove circuit board and battery.
3) Detach battery from circuit board and attach
new 9 volt.
4) Insert circuit board and battery into body.
5) Insert hinge tab into hinge hole (see picture
below) and pivot cap upward around hinge
until latched.
Mini LED Light
Operation: Push thumbwheel forward to light,
on two color modles, toggle switch left /right to
select LED color
Low battery Indication: White LEDs don't light,
Red LEDs light dimly. This is normal as white
LEDs require higher voltage.
How to change the battery:
1) Depress latch tab by pressing bump next to
thumbwheel, rotate cap out and down to
remove.
2) Remove circuit board and battery.
3) Detach battery from circuit board and attach
new 9 volt.
4) Insert circuit board and battery into body.
5) Insert hinge tab into hinge hole (see picture
below) and pivot cap upward around hinge
until latched.
Mini LED Light
Operation: Push thumbwheel forward to light,
on two color modles, toggle switch left /right to
select LED color
Low battery Indication: White LEDs don't light,
Red LEDs light dimly. This is normal as white
LEDs require higher voltage.
How to change the battery:
1) Depress latch tab by pressing bump next to
thumbwheel, rotate cap out and down to
remove.
2) Remove circuit board and battery.
3) Detach battery from circuit board and attach
new 9 volt.
4) Insert circuit board and battery into body.
5) Insert hinge tab into hinge hole (see picture
below) and pivot cap upward around hinge
until latched.