Star Headlight & Lantern 9500 Series - 58" Warning Package - Manual (Page 12)

-10-
LED Pattern Selection for Remote LED Flashers
1. Power up the LED heads you wish to program by applying power to the appropriate wire (s)
(usually Orange w/Red Stripe for remote flashers).
2. Briefly touch the Red w/Green stripe wire to +12VDC and release it, repeating this to
scroll through the patterns listed below. The cycle will repeat itself after the last pattern.
3. Once you find the pattern you wish to select, leave the Pattern Select wire
disconnected and turn the LEDs off. This will store the selected pattern.
8-Terminal LDF369 Flash Patterns (touch Red w/Green to +12VDC)
LED Pattern Programming
20-Terminal LDF398 Flash Patterns (touch Red w/Green to +12VDC)
Please Note: At any time during the programming sequence, you can reset the flash pattern back to the
default mode (Pattern 1 – Pursuit) by holding the red w/green Pattern Select wire to
+12VDC for 5 seconds, then releasing it.
1 Pursuit Mode (Default)
2 Alternating Slow Single (1-5 vs 6-10)
3 Alternate Pursuit Mode
4 Alternating Quad Flash (1-5 vs 6-10)
5 Alternating Triple (1,2,6,7,8 vs 3,4,5,9,10)
6 Alternating Quint (1,2,6,7,8 vs 3,4,5,9,10)
7 Simultaneous Slow Single (All Modules)
8
Simultaneous Fast Single (All Modules)
9 Simultaneous Triple Flash (All Modules)
10 Simultaneous Quad Flash (All Modules)
11 Simultaneous Quint Flash (All Modules)
12 Simultaneous Fast Triple Flash (All Modules)
13 Simultaneous Fast Quint Flash (All Modules)
14 In/Out Single (1,2,9,10 vs 3-8)
15 In/Out Triple (1,2,9,10 vs 3-8)
16 In/Out Quint (1,2,9,10 vs 3-8)
17 In/Out Single (1,2,3,8,9,10 vs 4-7)
18 In/Out Triple (1,2,3,8,9,10 vs 4-7)
19 In/Out Quint (1,2,3,8,9,10 vs 4-7)
20 1-5 Steady; 6-10 Single Flash
21 1-5 Steady; 6-10 Slow Single Flash
22 6-10 Steady; 1-5 Single Flash
23 6-10 Steady; 1-5 Slow Single Flash
24 Sequential Back And Forth
25 Sequential In/Out
26 Burst All w/ Alternating Burst
27 Alternating Burst w/ Sim. Double Then Quint
28 Simultaneous Burst w/ Alt. Double Then Quint
29 Hyper-Random
30 Demo
(Cycle Through Patterns 1-4,6-9,13-20,25-29)
LEDs in your lightbar are programmed using the Red w/Green stripe wire. If you have LEDs
controlled by an external flasher (LDF369 or LDF398), the pattern will be sett by touching the Red
w/Green wire to +12VDC. If you have Halo 360º LEDs, you will set the pattern by touching the Red
w/Green wire to ground.
NOTE: If at any time you would like to reset the pattern to the factory default (Pattern 28), simply
connect the Pattern Select wire to +12VDC for five seconds, then release it, and the default
pattern will be restored.
1. Slow Warn
2. Alt. Doubleflash, Flicker
3. All Double, Alt. Pre-Pop Triple, Slow Warn
4. Alternating Doubleflash, Non-Synch
5. Alt. Triple, Alt. Pre-Pop Triple, Flicker *
6. Alt. Quad, Flicker, Alt. Double, Flicker
7. Alt. Pre-Pop Quint, Alt. Quint, Flicker
8. All Tripleflash
9. Alt. Quadflash w/Post Pop
10. All Quadflash w/Post Pop
11. Alt. Quintflash
12. One Side Steady/Other Side Singleflash
†
13. Alt. Pre-Pop Quintflash
14. All Flicker
15. Alt. PSU Flicker
16. One Side Steady/Other Side Short-Long
†
17. One Side Rapid Fire, Other Side Pop
* = Default Pattern
† = California Title 13 Approved w/Red Steady/Blue Flashing
18. Comet 1
19. Alt Long Singleflash (Medium Warn)
20. Alt. Short - Alt. Long
21. Slow Warn, Alt. Tripleflash
22. Slow Warn, Super Fast Warn
23. All Doubleflash, Alt. Doubleflash
24. All Double, Alt. Double, Flicker
25. Fast Warn
26. Superfast Warn
27. Warn Fade
28. Pre-Pop Warn
29. All Singleflash
30. Alt. Tripleflash
31. All Quintflash
32. One Side Pop, Other Side Rapid Fire
33. Comet 2
34. Delta Omega
35. Cycle All Patterns