Syma Toys S6 - Manual

1
-1-
Cover
4“AAA” batteries
-2- -3-
-4- -5-
产品明细解图
1 2
3 4
7
24
23
22
21
20
19
18
17
16
15
14
8
5
9
12
10
11
13
6
-6- -7-
S6-01A S6-02 S6-03
S6-04A S6-05A S6-05B
S6-06A S6-07 S6-08
S6-09 S6-10
S6-01B
S6-11 S6-12
Headcover-Blue Headcover-Yellow Main blades Balance bar
Main frame-Blue
Tail assembly
-Blue
Base
Tail assembly
-Yellow
Transparent
cover
Battery Receicer board
Main frame-Yellow Motor A Motor B
S6-04B
S6-06B
USB charger cable Transmitter
ON CHA
OFF
80mm
83mm
25mm
60
mm
AGES 14+
S
6
3 CHANNEL REMOTE CONTROL HELICOPTER
IMPLEMENT STANDARD: GB/T26701-2011
INSTRUCTION MANUAL
Helicopter Features
A sophisticated built-in gyroscopic auto-stability system for smooth and stable flying.
Model design structured, easy operation and maintenance.
All material, dimensions and spare parts included in this instruction are for reference
only. The company is not responsible for any changes printed parts and notify
consumer. Any updated or changed please refer to our website www.symatoys.com.
Special Plastic frame for a good resistance to mill and stable flight.It is suitable for
indoor flight.
ABOUT CONTENTS
Product included
following contents:
Helicopter
Transmitter
Tail blade
Instruction manual
USB cable
GET TO KNOW YOUR TRANSMITTER
Remoter instruction
ON/OFF
Power/Charge
Indicator
Battery Installation
Up/Down
Forward/
Backward
Turn Left/
Turn Right
Turn left
trimmer
Turn right
trimmer High/Low
speed switch
(A/B Band
Selector)
Unscrew and remove battery cover from R/C unit, insert 4“AAA” batteries,noting
polarity indicator. Replace battery cover.
READY TO FLY YOUR HELICOPTER
Step 1: Press the power switch
to turn on the transmitter.
Step 2: Turn on your helicopter.
Step 3: Transmitter indicator blinks
for about 10-20 seconds to match
signal. When finish matching, it
keeps light on. please push the left
lever backwards to ready flight.
Horizontal
position
TIPS: When matching signal, keep
the helicopter on horizontal
position for faster matching
and starting start a stable flight.
FLIGHT CONTROL
Hover up and down Forward and backward
When the helicoptr fllies
steadity, you canshowly push
the throttle stick up to make
helicopter fly higher, or release
the stick a bit to make helicopter
fly lower. Only small amounts of
stick posoition change are
required for smooth flying.
When you push up the riht
contrl lever (steering rudder),
the nose incline to down, the
helicopter is moving to
forward. When you push down
the right control lever(steering
rudder), the nose incline to up,
the helicopter is moving to
backward.
Turn Left and Right Turn right/left calibration trim
Hold the helicopter at a height.
Push the rudder stick toward
left to turn counter clockwise,
and push the rudder stick
twoard right to turm clockwise. If helicopter rotates
clockwise…Continually
push right R/C calibration
until excessive turning stops.
If helicopter rotates counter
-clockwise…Continually
push right R/C calibration
until excessive turning stops.
HELICOPTER CHARGING
Charging helicopter with USB: Take out the
USB charging wire,connect the USB wire to
the computer interface. then connect the
other USB charging wire to the helicopter
interface. During charging, the indicator of
USBcharging wire will be OFF. When it fully
charged, the indicator will be ON.
Remote control charging
Charging time: about 25 - 30 minutes — Flying time: about 5 - 6 minutes!
Note:Make sure helicopter power switch to OFF position when charging.
TROUBLE SHOOTING
Problem Reson Solution
No response
from the
helicopter
1.Insufficient power with the helicopter. 1.Please charge to the helicopter.
2.Replace the battery inside the
transmitter.
3.Adjust the band on the transmitter
and keep it the same as the
helicopter.
2.Insufficient power with the transmitter,
power indicator keeps flashing.
3.The band of the transmitter does not
correspond to the decoding of the
helicopter.
If the
helicopter is
slow to
respond
or difficult to
manoeuver
1.Replace the battery.
2.Use the helicopter out of the range
of other RC helicopters.
1.Insuffcient power with the transmitter.
2.Transmitter of the same frequency is
used nearby.
A
A/B band selector：system regards to band “A” when
controller turned on. press button “A” for 2 seconds till
indicdtor lights flash twice,controller enter into bank "B",
press button “A” for 2 seconds, indicator lights flash one
time,controller back to band “A”.
BUTTON Description
BREAKDOWN & DIAGRAM
13
14
15
16
17
18
08
11
12
21
22
24
23
01
02
03
04
05
06
07
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
2
19 1
20 1
1
1
1
1 09 1
10 1
Code Description Quantity Code Description Quantity
Balance bar
Connector buckle
Main shaft base
Top blades locker
Below blades locker
Top blades
Spindle
Below blades
Below blades base
Top main stand
Top blade gear
Under blade gear
Battery
Under main stand
Receiver board
Top blades locker
main motor
Below blades locker
main motor
Tail tube
Tail dangling
Right body
Left body
Tail motor
Tail cover box
Tail blade
SPARE PARTS
All the spare parts below can bought from local distributor.
MAIN PARAMETER
80mm 83mm
3.7V 70 mAh Li-poly
25mm
60mm
Body length: Main blade diameter:
Main motor code: ∮6
Battery:
Body width:
Body high: