G-Shock G-2300EB-7 - Manual (Page 4)

Operation Guide 3192
4
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Button Operation Tone
The button operation tone sounds any time you press one
of the watch’s buttons. You can turn the button operation
tone on and off as desired.
• Even if you turn off the button operation tone, the
alarms, the Hourly Time Signal, and the countdown
alarm all operate normally.
MUTE indicator
To turn the button operation tone on and off
1. In the Timekeeping Mode, hold down A until the display contents start to flash.
This is the setting screen.
2. Press C nine times to display the current button operation tone setting ( or
).
3. Press D to toggle the button operation tone on ( ) or off ( ).
4. Press A to exit the setting screen.
• The MUTE indicator is displayed in all modes when the button operation tone is
turned off.
Power Saving Function
When turned on, the Power Saving function enters a sleep
state automatically whenever the watch is left in an area
for a certain period where it is dark. The table below
shows how watch functions are affected by the Power
Saving function.
Power saving on indicator
• Wearing the watch inside the sleeve of clothing can cause it to enter the sleep state.
• The watch will not enter the sleep state between 6:00 AM and 9:59 PM. If the watch
is already in the sleep state when 6:00 AM arrives, however, it will remain in the
sleep state.
To recover from the sleep state
Perform any one of the following operations.
• Move the watch to a well-lit area.
• Press any button.
• Angle the watch toward your face for reading.
Elapsed Time
in Dark
60 to 70 minutes
6 or 7 days
Display
Blank, with Power Saving
on indicator (
) flashing
Blank, with Power Saving
on indicator (
) displayed
(not flashing)
Operation
All functions enabled, except for the
display
Beeper tone, illumination, and display
are disabled.
To turn Power Saving on and off
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press C eleven times until the Power Saving on/off
screen appears.
3. Press D to toggle Power Saving on ( ) and off
( ).
4. Press A to exit the setting screen.
• The Power Saving on indicator ( ) is displayed in all
modes while Power Saving is turned on.
Auto Return
If you do not perform any operation for about two or three minutes while a setting
screen (with a flashing setting) is on the display, the watch will exit the setting screen
automatically.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls at high speed.
l ll
ll
ll ll
ll
l l l
lll
lll
ll
l
On/Off status
Initial Screens
When you enter the World Time Mode, or Alarm Mode, the data you were viewing
when you last exited the mode appears first.
Timekeeping
• Resetting the seconds to while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to
without changing the minutes.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced or the battery drops to Level 5.
• The current time for all city codes in the Timekeeping Mode and World Time Mode is
calculated in accordance with the Coordinated Universal Time (UTC) for each city,
based on your Home City time setting.
World Time
The seconds count of the World Time is synchronized with the seconds count of the
Timekeeping Mode.
Illumination Precautions
• The electro-luminescent panel that provides illumination loses power after very long
use.
• Illumination may be difficult to see when viewed under direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• Illumination turns off automatically whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
Lower than 15 degrees to
illuminate
Auto light switch precautions
• Avoid wearing the watch on the inside of your wrist. Doing so causes the auto light
switch to operate when it is not needed, which shortens battery life. If you want to
wear the watch on the inside of your wrist, turn off the auto light switch feature.
• Illumination may not turn on if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• Illumination turns off after a preset amount of time (1.5
or 3 seconds), even if you keep the watch pointed
toward your face.
• Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back toward you again. If this does
not work, drop your arm all the way down so it hangs at your side, and then bring it
back up again.
• Under certain conditions, illumination may not turn on until about one second after
you turn the face of the watch toward you. This does not necessarily indicate
malfunction of the auto light switch.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
Specifications
Accuracy at normal temperature: ± 15 seconds a month
Timekeeping: Hour, minutes, seconds, p.m. (P), month, day, day of the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City (can be assigned one of 48 cities); Standard Time / Daylight
Saving Time (summer time)
World Time: 48 cities (31 time zones)
Other: Daylight Saving Time/Standard Time
Alarms: 5 daily alarms (four daily alarms; one snooze alarm); Hourly Time Signal
Stopwatch:
Measuring unit: 1/100 second
Measuring capacity: 23:59' 59.99''
Measuring modes: Elapsed time, split time, two finishes
Countdown Timer:
Measuring unit: 1 second
Input range: 1 minute to 24 hours (1-minute increments and 1-hour increments)
Illumination: EL (electro-luminescent panel); Full Auto Light Switch; Selectable
illumination duration
Other: Button operation tone on/off, Power saving on/off
Power Supply: Solar cell and one rechargeable battery
Approximate battery operating time: 11 months (from full charge to Level 4)
under the following conditions:
• Watch not exposed to light
• Internal timekeeping
• Display on 18 hours per day, sleep state 6 hours per day
• 1 illumination operation (1.5 second) per day
• 10 seconds of alarm operation per day
Frequent use of illumination runs down the battery. Particular care is required
when using the auto light switch.
UTC Differential/City Code List
Pago Pago
Honolulu
Anchorage
Vancouver
Los Angeles
Edmonton
Denver
Mexico City
Chicago
New York
Santiago
Halifax
St. Johns
Rio De Janeiro
Fernando De
Noronha
Praia
Lisbon
London
Madrid
Paris
Rome
Berlin
Stockholm
Athens
Cairo
Jerusalem
–11
–10
–9
–8
–7
–6
–5
–4
–3.5
–3
–2
–1
+0
+1
+2
PPG
HNL
ANC
YVR
LAX
YEA
DEN
MEX
CHI
NYC
SCL
YHZ
YYT
RIO
FEN
RAI
UTC
LIS
LON
MAD
PAR
ROM
BER
STO
ATH
CAI
JRS
City
City
UTC
Code Differential
MOW
JED
THR
DXB
KBL
KHI
DEL
KTM
DAC
RGN
BKK
SIN
HKG
BJS
TPE
SEL
TYO
ADL
GUM
SYD
NOU
WLG
City
City
UTC
Code Differential
Moscow
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Kathmandu
Dhaka
Yangon
Bangkok
Singapore
Hong Kong
Beijing
Taipei
Seoul
Tokyo
Adelaide
Guam
Sydney
Noumea
Wellington
+3
+3.5
+4
+4.5
+5
+5.5
+5.75
+6
+6.5
+7
+8
+9
+9.5
+10
+11
+12
• Based on data as of December 2008.
• The rules governing global times
(GMT differential and UTC offset) and
summer time are determined by each
individual country.