G-Shock GT-2000-1M User Manual
Page 2
2263-2
ALARM MODE
When the Daily Alarm is turned on, the alarm
sounds for 20 seconds at the preset time each day.
Press any button to stop the alarm after it starts to
sound. When the Hourly Time Signal is turned on,
the watch beeps every hour on the hour.
•
The alarm sounds when the time selected for basic
timekeeping in the Timekeeping Mode (TIME 1 or
TIME 2) matches the alarm time you set.
To set the alarm time
1. Hold down
A
A
A
A
A
while in the Alarm Mode. The hour
digits flash on the display because they are
selected.
At this time the Daily Alarm is turned on
automatically.
2. Press
C
C
C
C
C
to change the selection in the following
sequence.
Hour
Minutes
3. Press
D
D
D
D
D
to increase the selected digits and
B
B
B
B
B
to decrease them. Holding down
either button changes the selection at high speed.
•
The format (12-hour and 24-hour) of the alarm time matches the format you
select for normal timekeeping.
•
When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning (no indicator) or afternoon (P).
4. After you set the alarm time, press
A
A
A
A
A
to return to the Alarm Mode.
•
If you do not operate any button for a few minutes while a selection is flashing,
the flashing stops and the watch goes back to the Alarm Mode automatically.
To switch the daily alarm and hourly time signal on and off
Press
D
D
D
D
D
while in the Alarm Mode to change the status of the daily alarm and
hourly time signal in the following sequence.
To test the alarm
Hold down
D
D
D
D
D
while in the Alarm Mode to sound the alarm.
Hourly Time
Signal Only
Daily Alarm
Only
Both OFF
Both ON
Alarm on indicator
Hourly time signal on indicator
(a) Elapsed time measurement
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
A
A
A
A
A
Start
Stop
Re-start
Stop
Clear
(b) Split time measurement
D
D
D
D
D
A
A
A
A
A
A
A
A
A
A
D
D
D
D
D
A
A
A
A
A
Start
Split
Split release
Stop
Clear
(c) Split time and 1st-2nd place times
D
D
D
D
D
A
A
A
A
A
D
D
D
D
D
A
A
A
A
A
A
A
A
A
A
Start
Split
Stop
Split release
Clear
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
First runner
finishes.
Second runner
finishes.
Record time of
first runner.
Record time of
second runner.
STOPWATCH MODE
The Stopwatch Mode lets you measure elapsed
time, split times, and two finishes. The range of
the stopwatch is 59 minutes, 59.99 seconds.
Mode indicator
Current
time
Minutes
Seconds
1/100 seconds
AUTO DISPLAY FUNCTION
The Auto Display function of this watch continually changes the contents of the display.
Note that you cannot use any of the watch’s other functions while the Auto Display
function is operating.
To turn the Auto Display on
Hold down
C
C
C
C
C
for about two or three seconds in any mode until the watch beeps.
To turn the Auto Display off
Hold down
C
C
C
C
C
for about two or three seconds until the watch beeps. At this time the
watch is in the Timekeeping Mode.
Note
The Auto Display function cannot be performed while you are making settings (i.e.
while digits or other setting are flashing on the display).
ADL
ADELAIDE
+9.5
ANC
ANCHORAGE
–09
BER
BERLIN
+01
BKK
BANGKOK
+07
CAI
CAIRO
+02
CCS
CARACAS
–04
CHI
CHICAGO
–06
DAC
DHAKA
+06
DEL
DELHI
+5.5
DEN
DENVER
–07
DXB
DUBAI
+04
GUM
GUAM
+10
HKG
HONG KONG
+08
HNL
HONOLULU
–10
IST
ISTANBUL
+02
JED
JEDDAH
+03
JRS
JERUSALEM
+02
KBL
KABUL
+4.5
KHI
KARACHI
+05
LAX
LOS ANGELES
–08
LON
LONDON
+00
MEX
MEXICO CITY
–06
MIA
MIAMI
–05
MIL
MILAN
+01
MLE
MALE
+05
NOU
NOUMEA
+11
NYC
NEW YORK
–05
PAR
PARIS
+01
PPG
PAGO PAGO
–11
RGN
YANGON
+6.5
RIO
RIO DE JANEIRO
–03
ROM
ROME
+01
SEL
SEOUL
+09
SFO
SAN FRANCISCO
–08
SIN
SINGAPORE
+08
SYD
SYDNEY
+10
THR
TEHRAN
+3.5
TYO
TOKYO
+09
WLG
WELLINGTON
+12
YVR
VANCOUVER
–08
CITY CODE TABLE
City Code
City
GMT differential
*
Based on data as of December 1997.
Mode
indicator
Minutes
Hourly time
signal on
indicator
Alarm on
indicator
PM
indicator
Hour
Current time