G-Shock GS-300-4B User Manual
Page 2
1798/2301-2
Viewing Result Mode Data
Press
B
B
B
B
B
to cycle through the best five lap times. Pressing
A
A
A
A
A
while a lap time is on
the display shows the average speed for the lap. Press
A
A
A
A
A
again to return to the lap
time.
•
Pressing
B
B
B
B
B
while the average speed is on the display advances to the next lap
time.
•
If the average speed is 1000 km/h or more, E r r is displayed in place of the average
speed.
Hour
Minutes
Hour
Minutes
Mode indicator
Hour Minutes
•
The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
•
When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon.
4. After you set the alarm time, press
A
A
A
A
A
to return to the Alarm Mode.
•
If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
To stop the alarm
•
Press any button to stop the alarm after it starts to sound.
To turn the Daily Alarm and Hourly Time Signal on and off
Press
B
B
B
B
B
while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
To test the alarm
Hold down
B
B
B
B
B
while in the Alarm Mode to sound the alarm.
Note that this operation also changes the Daily Alarm and Hourly Time Signal on/off
setting.
H-SET MODE
When the time shown on the display does not match the analog setting, use this
mode to correct the analog setting.
To set the analog time
1. Hold down
A
A
A
A
A
while in the H-SET Mode until the digital time (hour and minutes)
starts to flash on the display.
•
The following step changes the hands of the analog time-
piece without changing the flashing digital time.
2. Press
D
D
D
D
D
to advance the hand setting of the analog time-
piece. Holding down
D
D
D
D
D
changes the hand setting at high
speed.
•
Pressing
B
B
B
B
B
while holding down
D
D
D
D
D
causes the hand set-
ting to change at high speed. The hands continue to
move even when you release the buttons. Press
D
D
D
D
D
or
B
B
B
B
B
to stop them.
•
The analog time setting does not stop automatically when
it reaches the current time. You must stop the hands
manually.
•
Note that there is not function for moving the hands back,
so be sure that you stop any high-speed hand setting
operation before the time you want to set is reached.
3. After you set the analog time, press
A
A
A
A
A
to return to the H-SET Mode.
•
If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the H-SET Mode automatically.
Both OFF
Daily Alarm
Only
Hourly Time
Signal Only
Both ON
Mode indicator
Seconds
Hour
Minutes
Lap number
Order
Mode indicator
Stopwatch type
indicator
Lap time
Total time
Single Stopwatch
Lap number
(first starter)
Order
(first starter)
Stopwatch type
indicator
Lap time
(first starter)
Lap time
(second starter)
Lap number
(second starter)
Order
(second starter)
Dual Stopwatch
Mode indicator
Seconds
Hour
Minutes
Deleting Result Mode Data
Result Mode data is deleted automatically whenever you perform a new stopwatch
timing operation. To manually delete data, hold down
B
B
B
B
B
and
D
D
D
D
D
in the Result Mode
until the message CLR appears on the display.
DUAL TIME MODE
To set the Dual Time
1. Hold down
A
A
A
A
A
until the hour digits start to flash on the
display. The hour digits flash because they are select-
ed.
2. Press
C
C
C
C
C
to change the selection in the following se-
quence.
3. Press
D
D
D
D
D
to increase the number or
B
B
B
B
B
to decrease it.
Holding down either button changes the current num-
ber at high speed.
4. After you set the dual time, press
A
A
A
A
A
to return to the
Dual Time Mode.
•
The format (12-hour and 24-hour) of the dual time match-
es the format you select for normal timekeeping.
•
In the Dual Time Mode, the seconds count is synchronized with the seconds count
of the Timekeeping Mode.
•
If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Dual Time Mode automatically.
Switching Dual Time and the Current Time
Holding down
B
B
B
B
B
for about two seconds in the Dual Time Mode causes the Dual Time
and current time to be reversed. The hands of the watch move at high speed to the
correct time. To switch back, simply hold down
B
B
B
B
B
again in the Dual Time Mode.
ALARM MODE
When the Daily Alarm is turned on, an alarm sounds for
20 seconds at the preset time each day. When the Hourly
Time Signal is turned on, the watch beeps every hour on
the hour.
1. Hold down
A
A
A
A
A
until the hour digits start to flash on the
display. The hour digits flash because they are select-
ed. At this time the Alarm is automatically switched on.
2. Press
C
C
C
C
C
to change the selection in the following se-
quence.
3. Press
D
D
D
D
D
to increase the number or
B
B
B
B
B
to decrease it.
Holding down either button changes the current num-
ber at high speed.
Flashing