Saturn ST-HT7269 - Manual (Page 3)

4
the plug. Do not yank the
power cable.
 Demolition of the electric
heater with authorization is
strictly prohibited. Please look
for professional service
personnel if the heater is
damaged.
 The product is limited to home
use.
 Installation of the heater
directly under wall outlet is
strictly forbidden.
 During normal use, do not let
bare skin touch the surface of
the appliance, so as not to be
burnt
 Avoid the use of the heater if
children, animals or the
disabled and those who lack
self control are present while
nobody else is taking care of
them.
 The appliance should not be
available to the following
people (including children):
those with physical, sensory or
mental impairments, or those
who lack experience and
knowledge unless they get
custody or instructions on the
use of the product from the
person who is responsible for
their safety.
 Children should be supervised
and ensured that they will not
play with this appliance.
 Only specific personnel from
the technical service center
may replace the power cord of
the product in case it is
damaged to ensure safety.
 Do not share the socket with
other electrical appliances to
avoid current overload, or fire
risks may be caused by
excessive load
 CAUTION: covering of the
cooling device is prohibited
to avoid overheating, or
dangerous accidents may be
caused.
III. Installation and application
of the electric heater
 Check whether the parts are
complete and the product is
intact when open the
package.
 If you want to use the
electric heater in a mobile
way, please install the rollers
provided in the package.
Make sure the heater is
correctly fixed with the screws
provided. Please make sure the
base is level, stable and clean.
Please note the safe distance
mentioned below.
Steps for castor installation:
1. Put the product upside down on a
soft cotton cloth or carpet.
2. Mount the stand in the corresponding
location of the lower part of the product
as shown above, and then fix the
randomly supplied screw at the bottom
of the product with a screwdriver and
tighten the screw.
Wall-mount Instructions
Take out the wall brackets and
expansion screws out from the box, and
fix the screws onto the wall according to
the distances between holes of the wall
brackets, as depicted in the picture
below.
Aim the 4 holes in the back of the
machine to the 4 hooks on the wall
bracket and push it on, and then slide
Expansion Screw
5
into the slot to click on, as shown below.
Fix the wall bracket lock piece onto the
bracket with screws, slide the lock piece
into the locking slot on the back of the
machine, and then tighten up the screw,
as shown in the picture below.
Note: Prior to the drilling, make sure
there is no cable or other pipelines on
the wall to avoid damage. Remember
that the screws on the wall shall be
fixed and firm to ensure the safety
installation of the electric heater on the
wall. Please note the safe distance
mentioned below.
During installation, the heater must be
maintained sufficiently safe distance
from combustible materials and gas and
away from water.
During wall-hanging installation, keep
the installation height from the ground
greater than 15 cm. Hanging-type
heater shall be no less than 50 cm away
from the ceiling.
I ． Operation notice
Make sure the heater shell, line and
power plug are intact.
Check the rated voltage in the model
label of the heater is in line with that of
the outlet. Power outlet requirements
are: voltage 220V, frequency 50Hz,
bearing current ≥ 10A. Do not power
the heater on until the requirements are
met.
1. Turn the temperature control knob
clockwise to the end, press the level-I
power switch to switch on the low-level
heating, or the level-II switch for the
high-level heating. If both levels are
switched on, the machine will be
working on the maximum power.
2. Models with a 24 hour time-clock. To
program heating, proceed as follows:
a) Look at the time on your clock or
watch if it is 10.00, turn the numbered
timer disk clockwise until the number 10
on the disk coincides with the
on the
timer. Set the periods of time when you
want the appliance to work by pushing
the teeth inwards. Each tooth
corresponds to a period of 15 minutes.
This will leave visible sectors which
correspond to the periods of operation.
When set, the radiator will operate
automatically each day during the times
programmed (important the radiator
must always be plugged into the
socket.)
b) To change the programming, move
the teeth back into the initial position
and set the new periods of functioning
c) If you want to make the appliance
operate without programming , push all
the teeth into the centre. In this case,
to turn the mains to avoid continued
operation of the timer.
3. Models with mechanical 24 hour
timer (programming of delayed start.)
Wall Bracket
Lock Piece