Adtec digital EN-40 (version 2.02.24) - Manual

720X480 29i 19.40M
1DD 192K 2DD 192K 48
Front Panel Status
Video Resolution Frame Rate Video Bit Rate
Audio Input 1 & 2 Sampling Rate
Units ship with the front panel
logged in by default. If you become
logged out and are prompted for a
password, use the following key
sequence for access.
Press <Select> when panel displays
‘User Login -- logged out’
Press <Up arrow>
Press <Select>
Press <Enter>
Press <Right arrow>
Press <Enter>
Quick Start Guide
Getting Started
Thank you for your purchase of the Adtec EN-40 Encoder. This
product can be sold with an optional modulation hardware package.
Configurations and indicators relevant to that add-on package are noted
here. If you purchased this product without the modulator, please ignore
settings noted with an asterisks (*).
Further instructions are available via the manual integrated into the
on-board software. You can view it by looking for the HELP tab once your
unit is powered up and you are connected to the web-application. See back
for more details. This manual and the most recent firmware are available
on our support website, www.adtecinc.com. Advanced users can also find
direct API command help as part of the on-board web application.
System LED Status
Alarm
Off - No system alarms.
On - System alarm.
(Typically NTP alarm)
BISS
Off - No encryption set
On - Encryption active
Front Panel Menus:
Use Mode Button to move through top layer menus.
Use arrows for navigation in submenus.
Use select to enter into edit mode and enter to save selection.
Video
Off - If modulator is installed, ASI
Receive mode is enabled.
On - Video detected
Blink - No video detected and Fault
mode is enabled.
Encode
Off - No Encoding - Idle State
On - Device is encoding.
AVC
Off - MPEG 2 is selected for encode.
On - MPEG 4 (H264) is selected for
encode.
4:2:2
Off - Chroma type 4:2:0 is selected
for encode.
On - Chroma type 4:2:2 selected for
encode.
Front Panel LEDs:
Adtec Digital US Sales +1-615-256-6619 International Sales +1-904-394-0389 www.adtecinc.com ©2010 Adtec Digital
SELECT
1 2abc 3def
5jkl 6mno
7pqrs 8tuv 9wxyz
0
4ghi
F1 F2
ENTER
ESCAPE
MODE
4
S
IP Out RF Out Bars
IP Out
Off - Transport of IP via Ethernet
or GigE is idle.
On - Transport of IP via Ethernet
or GigE is active.
RF Out *
Off - Modulator is not enabled.
On - Modulator is transmitting.
Blink - Modulator is running in test
mode.
Bars
Off - B/T/ID options are disabled.
On - B/T/ID have been enabled.
A1 - A4
Off - Audio encoder configuration
is set to off.
On - Audio encoder configuration
is set to encode or passthru.
Busy
Off - No network activity
On - Network traffic present
Link
Off - No network detected
On - Network communication active
4
Encoder/Modulator
Encoder
Video
Encoder
Audio
Transmit PIDs Table Profile System
Login
Duration
Network
Time
NTP
Alarm
COM2
Firmware
Table
VBI Source
Closed Cap.
Service Name
Load
Save
Encrypt.
Mode
Clear Word
Encrypt Word
User ID 1
UserID 2
Auto TMR *
Mux Rate
Vid. AutoFill
IP Destinations 1-4
PCR
Prog. No.
Map PID
Vid. PID
Aud.1 PID
Aud. 2 PID
Aud. 3 PID
Aud. 4 PID
TS ID
AMOL
Splice
VITC Mode
VITC PID
Sample Freq.
A1 A2
A3 A4
Sync
Input
Mode
Type
Bitrate
Volume
Modulator *
Transmit
Mod. Type
Mod. Mode
Frequency
Power
Spec Inv.
FEC Frame
Roll Off
Pilot
Rate Prior.
Sym. Rate
Inter. Rate
Carrier Mode
Occ. Band.
Status
Rate
CODEC
Chroma
Input
ASI Rec.
GOP
GOP Str.
GOP Size
Latency
Hue
Brightness
Contrast
Saturation
SELECT ENTER
MODE
Device contains L-Band modulator
Device contains IF modulator
Device does not contain a modulator
Reset:
Should you need to
reset your device, you
can do so via the front
panel by pressing the
MODE, ESCAPE and
RIGHT ARROW keys
simultaneously.