Aervoe Emergency Light Center with 2 Flashlights - Manual (Page 2)

Wind ‘N Go ®
Emergency Light Center #7700, 7750
READ ALL INSTRUCTIONS BEFORE INSTALLING AND OPERATING
IMPORTANT SAFEGUARDS
•
Mount the charging center in an indoor, dry location using the instructions provided. Mount
according to instructions to avoid damage.
• To reduce the risk of electric shock, do not submerge. All components are water resistant but
not waterproof.
• Do not install the charging center or operate units in flammable or explosive environments
• Use only Class 2 UL approved, or equivalent, AC/DC power adapter (included)
• Do not operate the charging center or components if any damage is noticed
• Do not use on electrical circuits exceeding 120V AC
• Do not look directly at the light from the flashlight; may cause injury to your eyes
• Do not operate at temperatures above 120ºF or below 32ºF
• Turn off all lights before charging
• Charging center may be cleaned with a damp cloth and followed with a clean dry cloth. Dust
charging center regularly.
• Use only Wind ‘N Go units designed for use in this charging center. Other models could cause
damage and void the warranty.
• Administer close supervision around children.
PARTS IDENTIFICATION
A 3-station charging center is shown below. A 2-station charging center is also available. Models are
available featuring a combination of 2 or 3 #7111 Flashlights. See outside of the box for the contents
of your Emrgency Light Center.
MATERIALS NEEDED
 Pencil or Pen  Tape  Level  Awl or drill with 9/32” drill bit
 Hammer  Phillips head screw driver  Tape measure
MOUNTING & ASSEMBLY INSTRUCTIONS
1.
Locate a wall within 4 feet of an electrical outlet that would be easily accessible in total
darkness. The power cord should easily reach between the charging center and the outlet. An
ideal location would be near an exit door, electrical or maintenance room, laundry room, or
basement. It is not necessary to locate a wall stud to hang this unit.
2. Tape the included installation template on the designated wall and level. Mark the center
location for the two plastic wall anchors using a pen or pencil. Remove template.
3. Using an awl or drill, make holes for the plastic wall anchors that are just slightly smaller than
the anchor. Press the anchor into the hole until it is flush wit the surface. If necessary, gently tap
the anchor flush with a hammer.
4. Place the screw fastener into the opening of the anchor. Using a Phillips head screwdriver, drive
the screw 3/4 of the way into the fastener, leaving 1/4" exposed to mount the charging center.
5. Hang the center on the two screws by aligning the two mounting holes on the back over the
screws. Pull down gently to seat inside of the slots.
6. If the charging center does not sit flush against the wall, remove it and drive the screws into the
wall a little further and hang it again. If it still does not fit onto the exposed screws, then they
need to be backed out of the wall slightly. Repeat either step if necessary.
7. Plug the male end of the AC/DC adapter into the DC input port on the charging center and the
120V AC plug into an electrical outlet.
8. Seat units firmly into the charging pockets with the LED lens facing up and the power button
facing out. Be sure to seat it firmly onto the plug inside of the pocket.
9. Slide the power switch to the ON position. After this, the switch should stay in this position
to keep the units charged at all times. The Wind ‘N Go power indicator light at the top and the
small LED charging indicator lights under each pocket should be illuminated.
CHARGING
1.
The charging center will fully charge completely drained units within 10-12 hours for the
2-station charging center and 18 hours for the 3-station charging center. Time will vary
depending on the power stored and the number of units requiring a charge. Once fully charged,
the units will continue to receive a trickle charge so they are always ready for use.
2. If the power is out and the units have been used until they are completely dead, charge them up
by opening the hand crank and wind for emergency stand-by use.
REMOVING AND RETURNING UNITS FROM THE CHARGING CENTER
1.
When units are needed, open the clear protective cover and remove it by grasping and pulling
upward.
2. To return it to the charging center, slide it into the charging pocket with the LED lens facing up and
the power button facing out. Be sure to seat it firmly onto the plug inside of the charging pocket.
The LED indicator light will illuminate (see below).
INDICATOR LIGHTS
Wind ‘N Go power indicator light:
•
When plugged in and receiving power = steady red light
• During power outage = blinking red light so that it is easily detected in complete darkness
Charging indicator lights: When the units are seated inside of the charging pockets, a charging
indicator light will be illuminated.
•
GREEN = fully charged
• RED or RED/YELLOW = charge in process or the power is out
WIND ‘N GO FLASHLIGHT OPERATION
3 LED Light: (#7111)
Press the Power button:
•
1 time for 1 LED
• 2 times for 3 LEDs
• 3 times for off
Cell Phone Charging (#7111):
•
Winding for 3 minutes will generate power for a 1-3 minute emergency phone call.
• Longer winding will produce a longer power duration.
WALL MOUNTED CHARGING CENTER
Patent Pending
FLASHLIGHT PARTS IDENTIFICATION