Fire Magic Echelon Diamond Built-in Grill Quick Start Guide - Manual

REV 3 - 1306270115 L-C2-335
Outdoor Built-in
Gas Grill
Quick Start Guide
3-Installation
Robert H. Peterson Co.
CAUTION: For your safety read the installation instructions and owner’s manual provided with the grill.
These quick start instructions assume a natural gas or household propane confi gured unit. See main instructions for propane cylinder units.
Turn all gas control knobs on the grill to OFF. Attach the fl ex connector coming from the grill to the gas inlet pipe. Open the dedicated manual shut-off
valve. Test for leaks using a half-soap/half-water solution. Slide the unit into position in the enclosure. Do not pinch, kink, or damage the fl ex connector
(Fig. 3-3).
The control panel must be fl ush with the enclosure face as shown in Fig. 3-4.
Proper grill airfl ow must be maintained as shown in Fig. 3-5. Do not block. It is not necessary to remove the control panel or knobs for installation.
OFF Dedicated manual shut-off valve
y
Cut-out
Countertop
Hanger
Flex
connector
Gas inlet pipe
Top View
Maintain proper ventilation
airfl ow
Fig. 3-4
Control panel
must be fl ush with
enclosure face
Countertop
Overhang
Fig. 3-3
Fig. 3-5
CAUTION: Wind blowing into or across the rear oven lid vent (Fig.
3-1) can cause poor performance and/or dangerous
overheating. Orient the grill so that the prevailing wind
blows toward the front of the grill (Fig. 3-2).
CAUTION: To prevent dangerous overheating, the rear of the unit must have
a minimum clearance of 4” (10.2 cm) from any backsplash/wall.
Fig. 3-2
CORRECT
PLACE GRILL SO PREVAILING WIND
BLOWS TOWARD FRONT OF GRILL
YOU MUST PROTECT REAR OVEN
VENT FROM PREVAILING WIND
Rear oven lid vent
INCORRECT
Fig. 3-1
INSTALLER: Leave these instructions with consumer. CONSUMER: Retain for future reference.
This grill must be installed in accordance with local codes and ordinances, or, in the absence of local codes, with either the latest National Fuel Gas Code (ANSI
Z223.1/NFPA 54), and Natural Gas and Propane Storage and Handling Installation Code (CSA-B149.1).
This appliance and its individual shutoff valves must be disconnected from the gas-supply piping system when testing the system at pressures in excess of ½ psig.
This appliance must be isolated from the gas-supply piping system by closing its dedicated manual shutoff valve during any pressure testing of the gas-supply
system at pressures up to and including ½ psig.
This grill is designed for outdoor use only. DO NOT use this grill under unprotected fl ammable surfaces. DO NOT use this grill inside a building, garage,
enclosed area, or an unprotected covered area (see paragraph below). DO NOT use this grill in or on a recreational vehicle or boat.
Important: When installing this grill in a COMBUSTIBLE surround, an R.H. Peterson insulating liner must be used. See the Fire Magic Insulating
Liner Instructions.
If installed or used under a patio roof, the cooking grid area must be fully covered by an exhaust hood with a vent. An exhaust fan with a rating of 1,000 CFM (cubic feet
per minute) (472 liters per second) or more may be necessary to effectively remove smoke and other cooking by-products from the area under the hood. Fire Magic Vent
Hoods are available to meet this requirement. This outdoor grill must not be used under overhead unprotected combustible construction. THIS UNIT MUST NOT BE
LOCATED IN A FULLY ENCLOSED AREA OF ANY KIND.
2-Unpacking
Carefully unpack the grill, removing all packing material and protective fi lm. Verify that all
parts have arrived undamaged by consulting the parts list in the owner’s manual. Remove
foam packed hardware from oven area. (See Fig. 2-1.)
Consult the parts list in the owner’s manual. If any parts are missing or damaged,
immediately contact the Fire Magic dealer before beginning installation.
Fig. 2-1
1-Safety
Lift out foam packed hardware
Remove plastic
zip-ties
Location
Connect Gas supply
ECHELON
diamond series
NOTE: THE CONTROL PANEL DOES NOT NEED TO BE REMOVED
FOR INSTALLATION. IF REMOVAL IS REQUIRED IT MUST
BE DONE WITH CAUTION BY A QUALIFIED PROFESSIONAL
SERVICE TECHNICIAN, TO PREVENT ANY POSSIBLE WIRE
DISCONNECTIONS.