Fusion CA-DA41400 - Manual (Page 2)

AMPLIFIER SPECIFICATIONS
CA-DA12250 CA-DA41400 CA-DA51600
Peak Power (Watts) 2250 1400 1600
Frequency Response 10Hz - 250Hz 10Hz -65kHz 10Hz -50kHz
Dimensions (mm)
300(l) x 210(w) x 50(h)
11-13/16 x 8-1/4 x 2”
300(l) x 210(w) x 50(h)
11-13/16 x 8-1/4 x 2”
300(l) x 210(w) x 50(h)
11-13/16 x 8-1/4 x 2”
Power Ratings
500W RMS x 1 @ 4Ω 1%
THD+N
150W RMS x 4 @ 4Ω 1%
THD+N
80W RMS x 4 +
250W RMS x 1 @ 4Ω 1%
THD+N
850W RMS x 1 @ 2Ω 1%
THD+N
220W RMS x 4 @ 2Ω 1%
THD+N
130W RMS x 4 +
330W RMS x 1 @ 2Ω 1%
THD+N
1100W RMS x 1 @ 1Ω 1%
THD+N
440W RMS x 2 @ 4Ω
Bridged 1% THD+N
250W RMS x 2 @ 4Ω
Bridged 1% THD+N +
250W RMS x 1 @ 4Ω 1%
THD+N
INSTALLATION GUIDELINES
1. Ensure the +12V lead is disconnected from
the battery before you connect any new
equipment.
2. Ensure the mounting location will not
interfere with the gas tank, brake lines or
electrical wiring.
3. Ensure the Amplifier is securely fastened to
the vehicle to prevent injury in the event of
an accident.
4. Ensure all wiring is protected to avoid
pinching or crushing which could result in
damage to the audio system.
5. Ensure the mounting location has sufficient
air flow around the amplifier. If the amplifier
is mounted in an enclosed space a 3” fan
with ducting should be used to aid in air
flow.
6. Do not mount any amplifier on a subwoofer
enclosure as extended exposure to vibration
may cause malfunction of the amplifier.
7. Ensure you use the recommended gauge
wire/cable for all amplifier connections.
WIRING
1. Ensure the audio system is turned off before
making any connections to the amplifier,
speakers or source unit, failure to do so could
result in permanent damage to the audio
system.
2. When wiring the FUSION amplifier ensure
that the cable is protected from sharp objects
and always use rubber grommets when wiring
through metal panels.
3. Ensure all terminals and connections are
protected from the vehicle chassis and from
each other as failure to do so could result in
permanent damage to the audio system.
POWER
FUSION amplifiers should be connected directly
to the +12V battery terminal with an inline fuse or
circuit breaker as close the battery as possible.
GROUND
When grounding/earthing your amplifier ensure that
the location is a good source of ground (preferably
the floor pan). Make sure the metal is clean of paint
etc as a poor earth could damage your audio system.
REMOTE TURN ON
This connection turns the amplifier on & should be
connected to the remote turn on wire from the Head
Unit. If one is not available a switched 12v source must
be used. Either a power antenna wire or ACC +12V.
LOW LEVEL INPUTS
Choose the correct length RCA cable & run them to the
RCA outputs of the source/head unit, avoiding running
beside other looms & or power cable.
For specific wiring information please
refer to www.fusionelectronics.com