Harken Rollpin replacement kit - Manual

I N S T R U C T I O N S H E E T
Jib Reefing & Furling
Rollpin Replacement Kit
1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.
Telephone: (262) 691-3320 • Fax: (262) 691-3008
Web: http://www.harken.com • E-mail: [email protected]
Rollpins Paper Towels
Loctite ® 277 (Red) Hammer
Wood Support Block Center Punch
Flushing Punch Vice-Grip-type pliers
Loctite ® Primer “N” (HFG395) Rollpin Punch (available from Sears:
3 / 32 ” for #1, 1 / 8 " for #2)
Supplies Included Supplies You Need
Checking Joints
1. Take headstay down and remove lower drum assembly and feeder.
2. Recess threaded stud into bottom foil to allow room on wire to take
joints apart for re-gluing. If you have a Norseman
® , Sta-lok ® or Navtec ®
terminal, take bottom joint apart as directed below to allow space on
wire to separate foils.
3. Support joint area in the Wood Support Block (included). Use a Roll
Pin Punch to drive pin out or pound new rollpin half-way into foil, to
push old pin out half-way.
4. Pull both pins out of foil using vice-grips or pliers.
5. Try pulling foil sections apart. If they come apart, foils need
to be re-glued to connectors.
Continued
I N S T R U C T I O N S H E E T
Jib Reefing & Furling
Rollpin Replacement Kit
1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.
Telephone: (262) 691-3320 • Fax: (262) 691-3008
Web: http://www.harken.com • E-mail: [email protected]
Rollpins Paper Towels
Loctite ® 277 (Red) Hammer
Wood Support Block Center Punch
Flushing Punch Vice-Grip-type pliers
Loctite ® Primer “N” (HFG395) Rollpin Punch (available from Sears:
3 / 32 ” for #1, 1 / 8 " for #2)
Supplies Included Supplies You Need
Checking Joints
1. Take headstay down and remove lower drum assembly and feeder.
2. Recess threaded stud into bottom foil to allow room on wire to take
joints apart for re-gluing. If you have a Norseman
® , Sta-lok ® or Navtec ®
terminal, take bottom joint apart as directed below to allow space on
wire to separate foils.
3. Support joint area in the Wood Support Block (included). Use a Roll
Pin Punch to drive pin out or pound new rollpin half-way into foil, to
push old pin out half-way.
4. Pull both pins out of foil using vice-grips or pliers.
5. Try pulling foil sections apart. If they come apart, foils need
to be re-glued to connectors.
Continued
I N S T R U C T I O N S H E E T
Jib Reefing & Furling
Rollpin Replacement Kit
1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.
Telephone: (262) 691-3320 • Fax: (262) 691-3008
Web: http://www.harken.com • E-mail: [email protected]
Rollpins Paper Towels
Loctite ® 277 (Red) Hammer
Wood Support Block Center Punch
Flushing Punch Vice-Grip-type pliers
Loctite ® Primer “N” (HFG395) Rollpin Punch (available from Sears:
3 / 32 ” for #1, 1 / 8 " for #2)
Supplies Included Supplies You Need
Checking Joints
1. Take headstay down and remove lower drum assembly and feeder.
2. Recess threaded stud into bottom foil to allow room on wire to take
joints apart for re-gluing. If you have a Norseman
® , Sta-lok ® or Navtec ®
terminal, take bottom joint apart as directed below to allow space on
wire to separate foils.
3. Support joint area in the Wood Support Block (included). Use a Roll
Pin Punch to drive pin out or pound new rollpin half-way into foil, to
push old pin out half-way.
4. Pull both pins out of foil using vice-grips or pliers.
5. Try pulling foil sections apart. If they come apart, foils need
to be re-glued to connectors.
Continued
I N S T R U C T I O N S H E E T
Jib Reefing & Furling
Rollpin Replacement Kit
1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.
Telephone: (262) 691-3320 • Fax: (262) 691-3008
Web: http://www.harken.com • E-mail: [email protected]
Rollpins Paper Towels
Loctite ® 277 (Red) Hammer
Wood Support Block Center Punch
Flushing Punch Vice-Grip-type pliers
Loctite ® Primer “N” (HFG395) Rollpin Punch (available from Sears:
3 / 32 ” for #1, 1 / 8 " for #2)
Supplies Included Supplies You Need
Checking Joints
1. Take headstay down and remove lower drum assembly and feeder.
2. Recess threaded stud into bottom foil to allow room on wire to take
joints apart for re-gluing. If you have a Norseman
® , Sta-lok ® or Navtec ®
terminal, take bottom joint apart as directed below to allow space on
wire to separate foils.
3. Support joint area in the Wood Support Block (included). Use a Roll
Pin Punch to drive pin out or pound new rollpin half-way into foil, to
push old pin out half-way.
4. Pull both pins out of foil using vice-grips or pliers.
5. Try pulling foil sections apart. If they come apart, foils need
to be re-glued to connectors.
Continued