Legrand WIUC20GL - Manual

WHILE-IN-USE COVER DESCRIPTION
This product is a weatherproof cover that is intended to enclose an
electrical device (outlet, GFCI, switch, etc.) and protect the device
from inclement weather even when a plug and cord are inserted in it.
It is designed to install quickly and easily (see instructions below) and
provide an attractive, durable finish that will yield long-lasting results.
APPLICATION
The cover should be installed in areas subject to saturation from water
or other liquids, (see description for “Wet Location” and “Damp
Location” in the National Electrical Code). The cover can be mounted
horizontally or vertically, as long as the hinge is in the top corner. See
Figure 1 (A-D) for applicable mounting and attachment options. The
cover includes multiple plates, so it can be used to cover different
types of electrical devices.
WARNING - Turn off all power to circuit before installing this
device. Improper wiring of any electrical device can cause seri-
ous injury or death. These wiring devices should only be
installed by an Electrician or other qualified person
.
CAUTION - This cover should be installed in accordance with the
National Electrical Code, and all applicable local codes and standards.
INSTALLATION INSTRUCTIONS
NOTE:
The cover should be installed on a smooth, flat, non-porous
surface. To install on an irregular surface, use a proper amount of
caulking to ensure a watertight seal between the back of the cover
and the mounting surface.
1. Disconnect power to circuit by removing fuse or turn circuit breakers
to OFF before installing.
2. Remove the existing receptacle cover, if any, and discard.
3. Back off the mounting screws that hold the GFI or receptacle to
the junction box but do not remove screws.
4. Insert mounting screws through the keyhole shaped mounting holes
on assembly and slide the assembly to the left (see Figure 2).
Center the device in the box. Tighten screws.
5. If mounting to an FS or outdoor junction box use the four screws
provided to further secure the assembly to the box.
6. DO NOT OVER TIGHTEN SCREWS.
7. Choose appropriate wall plate and snap in by putting one long
edge in place first and rotating the plate over the device. (If device
is in the way, loosen screws and move left or right.) Discard
other plate(s).
8. For best rain protection, be sure to route cords through the cord
outlet and press the cover firmly until it snaps closed. Position
cord gaskets as shown in Figure 3.
LIMITED ONE YEAR WARRANTY
Pass & Seymour will remedy any defect in workmanship or material in Pass & Seymour products which
may develop under proper and normal use within one year from date of purchase by a consumer:
(1) by repair or replacement, or, at Pass & Seymour's option, (2) by return of an amount equal to
consumer's purchase price. Such remedy is IN LIEU OF ANY AND ALL EXPRESSED OR IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Such
remedy by Pass & Seymour does not include or cover cost of labor for removal or reinstallation of the
product. ALL OTHER FURTHER ELEMENTS OF DAMAGE (INCIDENTAL OR CONSEQUENTIAL
DAMAGES) FOR BREACH OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ARE EXCLUDED HEREBY. (Some states do not allow disclaimers or exclusion or
limitation of incidental or consequential damages, so the above disclaimer and limitation or exclusion
may not apply to you.) ANY IMPLIED WARRANTIES INCLUDING WHERE REQUIRED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE
LIMITED TO THE ONE YEAR PERIOD SET FORTH ABOVE. (Some states do not allow limitations
on how long an implied warranty lasts, so the above limitation may not apply to you.)
To insure safety, all repairs to Pass & Seymour products must be made by Pass & Seymour, or under
its specific direction. Procedure to obtain performance of any warranty obligation is as follows:
(1) Contact Pass & Seymour, Syracuse, New York 13221, for instructions concerning return or repair;
(2) return the product to Pass & Seymour, postage paid, with your name and address and a written
description of the installation or use of the Pass & Seymour product, and the observed defects or
failure to operate, or other claimed basis for dissatisfaction.
TradeMaster ®
WEATHERPROOF WHILE-IN-USE COVER
INSTALLATION INSTRUCTIONS
Figure 1
A B
C D
Figure 2 Figure 3