Marantz AV9000 - Manual (Page 18)

ENGLISH
13
LEVEL 1/2 (SPEAKER LEVEL BY TEST TONE)
SPKR LEVEL
TEST TONE:
Press the OK button, ON is indicated and the test tone
starts from the front L-CH speaker. Press the OK
button again, OFF is indicated and the output of the
test tone will stop.
MODE: Select the mode for generating the test tone. If you
select AUTO, test tone will be output in a circular
pattern which is Left
→ Center → Right → Surround
Right → Surround Left → Subwoofer → Left →... 3
seconds for each channel. If you select MANUAL,
press the
OK or CH+ button to select the test tone
channels.
Channel: Adjust the level of test tone for each channel with the
LVL+ , LVL– or / buttons of the RC-18SR. The
current volume level is shown at the center of the
display.
Notes:
The setup level for each channel is memorized to reproduce the all
surround mode. These levels are common for all surround modes,
except 6CH-DIRECT mode.
LEVEL 2/2 (BASS PEAK LEVEL LIMIT)
With Dolby Digital and DTS , not only the LFE (Low Frequency
Effects), but also the bass of all channels can be heard from the
Subwoofer or Large-speakers. This procedure prevents these
speakers from becoming too loud and creating an unbalanced
sound. Since the sound is output at a loud volume, perform this
operation carefully.
TEST SIGNAL: Press the OK button, START is indicated and a Bass
test tone is generated from the speaker, according to
SPK size setup. But the sound is not heard because
the Master volume is set to
∞ automatically. Press
button to move the cursor to VOLUME control.
VOLUME: Adjust the bass test tone output level to where the
bass sound begins to distort or maximum level with
the
VOL+ , VOL– or / button. Press button to
move the cursor to ENTER.
ENTER: Press the OK button, ENTER is blinking and the Bass
test tone stops. The Bass Peak Limit Level for your
system has been memorized
Notes:
Each time the subwoofer level is changed, perform the Bass Peak
Level setup and correct the setting. The bass peak limiter is not
effective in STEREO reproducing for analog input and 96kHz-PCM, or
SOURCE-DIRECT and 6CHANNEL-DIRECT modes are selected.
The selected value is displayed in the volume column before the test
signal starts.
SURROUND MODE
MODE: Select the surround mode with or button.
NIGHT MODE: Switch the NIGHT MODE ON or OFF with the or
button. Selecting the Night Mode ON is effective in
Dolby Digital only, and it compresses the dynamic
range by up to 1/4 to 1/3. This softens loud passages
such as sudden explosions, to help prevent
disturbing others late at night.
LFE LEVEL: Select the output level of the LFE signal included in
the Dolby Digital signal or the DTS signal. Select 0
dB, -10 dB or OFF with or button. The level is
ordinarily set to 0 dB except DTS-Music mode. In the
DTS-Music mode, default level is set to -10 dB.
REC COPY
VCR1 COPY
Select the visual source of the VCR1 output with or button for
video and audio dubbing to the VCR1 deck.
The source is switched in the following sequence.
SOURCE
→ TV → LD → DVD → DSS/VCR2 → AUX → SOURCE → .....
To determine each source, display the desired source and press the
OK button or / button.
TAPE COPY
Select the audio source of the TAPE output with or button for
audio dubbing to the tape deck.
The source is switched in the following sequence.
SOURCE
→ TUNER → CD → CD-R/MD → SOURCE → ....
To determine each source, display the desired source and press the
OK button or / button.
LEVEL 1/2 SPKR LEVEL
TEST TONE :
OFF
MODE : MANUAL
FRONT L : 0 dB
TO NEXT LEVEL MENU
LEVEL 2/2 BASS LEVEL
BASS PEAK LEVEL
TEST SIGNAL : STOP
VOLUME : - 75dB
ENTER
RETURN TO MAIN/EXIT
SURROUND MODE
MODE : STEREO
NIGHT MODE : OFF
LFE LEVEL : OdB
RETURN TO MAIN/EXIT
REC COPY
VCR1 : SOURCE
TAPE : SOURCE
D I G I TA L : SOURCE
RETURN TO MAIN/EXIT