Metro Basic Entry Touchpad - Manual

®
InterMetro Industries Corporation
North Washington Street, Wilkes-Barre, PA 18705
For Product Information Call: 1-800-433-2232
Visit Our Web Site: www.metro.com
USER MANUAL
BASIC ENTRY TOUCHPAD
USER MANUAL
TM
®
BEFORE OPERATING
TOUCHPAD,
CHARGE SYSTEM
FOR 4 HOURS.
Sleep Mode:
In order to conserve battery life, the
touchpad unit will enter into a “Sleep
Mode” if the unit has not been used for
4 hours. Once the unit has been fully
charged and the charging system has
switched to trickle charge, the unit will
enter into a sleep mode. Nothing is
necessary to “wake up” the unit. Enter
the password in to unlock the unit. You
may need to enter the password twice.
BASIC TOUCH PAD
OPERATION
(See Note 1)
1) NORMAL OPERATION (See Note 2)
TO UNLOCK UNIT —
User, Pharmacist, or Supervisor
1. Enter 4, 5, or 6 digit code —
(#, #, #, #, #, #).
System turns on with first # pressed.
If code is VALID system will automatically
unlock with the last # entered (Green light
will illuminate on touchpad).
If code is INVALID system will give one
long beep, or no beep if less than 6
digits are entered. (Return to Step 1).
If THREE INVALID Codes are entered in a
row the system will enter the “Access
Denied” function, and respond with one
long beep if a number key is depressed
(See Note 3).
NOTE 1: The keypad will terminate any ongoing transaction if a key has not been pressed in 30 seconds.
NOTE 2: The key lock should be in the locked position, the key is vertical and aligned with orange dot.
NOTE 3: For security reasons, once the user begins a transaction (normal operation by pressing the PIN key to
change code, or changing the access times by pressing the “TIME” key), they are committed to the successful
entry of the PIN number to perform the particular function. Failure results in being denied access to that particular
function only for the specified access denials time. While the other functions will not be impeded by one function
denied, pressing the first key for that function (e.g., PIN or TIME) will reset the timer for that procedure. The typical
user may want to keep this tamper-protection feature set to a relatively short time, 1-2 minutes.
USER MANUAL
For Basic Entry Touchpad
TO LOCK UNIT
The System will AUTOMATICALLY relock
on a user-defined time frame.
This time is a Supervisor programmable
function.
To RELOCK NOW Press LOCK Key.
2) CHANGE PINs
(Supervisor Function Only)
1. Press PIN key.
2. Enter the Supervisor PIN Code (This is
either a 4, 5, or 6 digit code).
If the code is VALID the system will give
three short beeps.
If not, there will be one long beep. There
may not be any beeps if a 4 digit code
was entered and the required code is a
5 or 6 digit code.
If three invalid codes are entered, you will
be denied access until the preset
“Access Denied Time” has expired.
3. Depress the:
“1” key to Change the Nurse PIN.
“2” key to Change the Pharmacy PIN.
“3” key to Change the Supervisor PIN.
4. Enter a new 4, 5, or 6 digit code
followed by the PIN key.
5. Reenter the PIN code followed by the
PIN key to confirm.
• If the numbers match, the system will
give three short beeps.
• If they do not match, the system will
give one long beep, you will need to
return to Step 4.
• Clear will Exit this routine after the
supervisor’s PIN has been entered.
3) CHANGE AUTOMATIC RELOCK
TIME (Supervisor Function Only)
1. Press TIME Key.
2. Enter 4, 5, or 6 digit Supervisor code —
(#, #, #, #, #, #).
If code is VALID system will give three
short beeps.
If code is INVALID system will give one
long beep or no beep if less than 6 digits
are entered. (Return to Step 2).
If THREE INVALID Codes are entered in a
row the system will enter the “Access
Denied” function, and respond with one
long beep if the time key is depressed.
3. Depress the:
“1” key for Auto-Relock Time.
“2” key for Access Denied Time.
4. Enter Minutes for Auto-Relock or
Access Denied Time (00-99).
(00'= approx. 15 seconds).
NOTE: This is a two-digit number that will
scroll. i.e., If you enter “1,” “2,” “3” the
system will keep the last two numbers
(23 minutes). Minutes 1-9 must be
preceded with a “0” (i.e., 5 minutes=05)
5. Press TIME Key and system will give
three short beeps to confirm entry and
Exit routine.
CLEAR will Exit this routine after the
Supervisor PIN has been entered.
Factory Defaults when cart arrives:
Supervisor Code — ‘000000’
User Code — ‘000000’
Pharmacist Code — ‘000000’
Access Denied Time — 5 minutes
Auto Relock Time
— 5 minutes