Microsonic lcs+340/F - Manual

Operating Instructions
Ultrasonic proximity switch with
one switched output and IO-Link
interface
lcs+340/F
lcs+600/F
Product description
The lcs+ sensor offers a non-contact
measurement of the distance to an
object which must be positioned
within the sensor’s detection zone.
The switched output is set condi-
tional upon the adjusted detect dis-
tance.
Via the Teach-in procedure, the de-
tect distance and operating mode
can be adjusted. One LED indicates
operation and the state of the swit-
ched output.
The lcs+ sensors are IO-Link-capable
in accordance with IO-Link specifica-
tion V1.0.
Safety instructions
 Read the operating instructions
prior to start-up.
 Connection, installation and ad-
Sensor adjustment with Teach-in procedure
Set detect point
– method A
Place object at position 1.
Press T2 for about
3 s, until both LEDs flash
simultaneously.
Both LEDs: flash alternately
Set detect point +8 %
– method B
Place object at position 1.
Press T2 for about
3 s, until both LEDs flash
simultaneously.
Both LEDs: flash alternately
Set window mode Set two way reflective
barrier
Set NOC/NCC
Place object at position 1. Place reflector at
position 1.
Press T2 for about
3 s, until both LEDs flash
simultaneously.
Both LEDs: flash alternately
Press T2 for about
3 s, until both LEDs flash
simultaneously.
Both LEDs: flash alternately
Press T2 for about 13 s,
until both LEDs flash
mutually.
LED D1:
LED D2:
flashes
on: NOC
off: NCC
Activate/deactivate
Teach-in
Switch off operating
voltage.
Reset to factory setting
Switch off operating
voltage.
While pressing T1 turn on
operating voltage.
Keep T1 pressed for about
3 s, until both LEDs flash
simultaneously.
LED D2:
LED D1:
flash
on: Teach-in
activated
off: Teach-in
deactivated
While pressing T1 turn on
operating voltage.
Keep T1 pressed for about
13 s, until both LEDs
flash mutually.
Press T2 for about 1 s.
Normal mode operating
Press T2 for about
3 s, until both LEDs flash
mutually again.
Place object at position 2.
Both LEDs: flash mutually
Press T2 for about 1 s. Press T2 for about 10 s.
To change output
characteristic press T2 for
about 1 s.
Wait for 10 s.
To activate/deactivate
Teach-in press T1 for
about 1 s.
Wait for 10 s
Normal mode operating
justments may only be carried out
by qualified staff.
 No safety component in
accordance with the EU Machine
Directive.
Use for intended purpose only
lcs+ ultrasonic sensors are used for
non-contact detection of objects.
Installation
 Mount the sensor at the place of
fitting.
 Connect a connection cable to the
M12 device plug.
Start-up
 Connect the power supply.
 Carry out sensor adjustment in
accordance with the diagram.
Fig. 1: Pin assignment with view onto sensor
plug and colour coding of the
microsonic connection cables
Factory setting
 Switched output on NOC.
 Detect distance at operating range.
Operating modes
Three operating modes are available
for the switched output:
1
3
colour
+U B
-U B
brown
blue
4
2
5
F
-
black
white
Sync grey
1
5
2
3 4
 Operation with one detect point
The switched output is set when the
object falls below the set detect
point.
 Window mode
The switched output is set when the
object is within the set window.
 Two-way reflective barrier
The switched output is set when the
object is between sensor and fixed
reflector.
Fig. 2: Assembly distances
≥ 2,00 m ≥ 18,00 m
≥ 4,00 m ≥ 30,00 m
A B
Synchronisation
If under multiple sensor operation
the assembly distance falls below the
values shown in Fig. 2, the internal
synchronisation should be used. For
this purpose interconnect each pin 5
of max. 10 sensors.
Maintenance
microsonic sensors are maintenance-
free. In case of excess caked-on dirt
we recommend cleaning the white
sensor surface.
Notes
 The sensors of the lcs+ family have
a blind zone, within which a dis-
tance measurement is not possi-
ble.
 The lcs+ sensors are equipped
with an internal temperature com-
pensation. Due to the sensors self
heating, the temperature compen-
sation reaches its optimum work-
ing-point after approx. 30 minutes
of operation.
 In the normal operating mode, an il-
luminated yellow LED signals that the
switched output is switched
through.
 The lcs+ sensors have a push-pull
switched output.
 In the »Two-way reflective barrier«
operating mode, the object has to
be within the range of 0-85 % of
the set distance.
 In the »Set detect point – method
A« Teach-in procedure the actual
distance to the object is taught to
the sensor as the detect point. If
the object moves towards the
sensor (e.g. with level control) then
the taught distance is the level at
which the sensor has to switch the
output.
 If the object to be scanned moves
into the detection area from the
side, the »Set detect point +8 % –
method B« Teach-in procedure
should be used. In this way the
switching distance is set 8 % fur-
ther than the actual measured dis-
tance to the object. This ensures a
reliable switching distance even if
the height of the objects varies
slightly.
Ultrasonic Sensors
Set switched output Further Settings