Skutch Electronics BA-1000 User Manual
Page 5
Version 6.xx
Page 5
transferred directly into the BA-1000 system. The
software package can be used on PC’s running
Windows 95, 98 or ME with a USB interfaced CF
Card Reader.
P
P
o
o
w
w
e
e
r
r
O
O
u
u
t
t
P
P
r
r
o
o
t
t
e
e
c
c
t
t
e
e
d
d
The numbers stored on disk and the setup and clock
information is backed up with a 10 year battery. If
power fails at any time, the unit will remember if it
was dialing or in answer mode, and it will pick up
where it left off.
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
L
L
o
o
c
c
a
a
t
t
i
i
o
o
n
n
When selecting a location for the system, the
following conditions MUST be avoided:
Temperatures above 95°°°°F.
Temperatures below 65°°°°F.
Carpeted areas that produce Static Electricity.
High dust/tobacco smoke areas.
Exposure to direct sunlight.
The SYSTEM and the POWER CUBE should be
located in a well ventilated area. It should be noted
that the POWER CUBE can get quite warm during
operation. Make sure that both a three-prong power
outlet and a proper telephone jack are within six feet
of the installation site.
P
P
o
o
w
w
e
e
r
r
The SYSTEM can be used on a three-prong
grounded 110VAC power outlet. This is needed for
proper protection of the unit's circuitry. Power
circuits that are used for any heavy equipment such
as large freezers, blowers, heaters, copiers, or any
electrical equipment that contains large motors,
should be avoided. Heavy electrical equipment can
cause power glitches over the power line which
could interfere with the operation of the system. If
your power lines are excessively noisy a power filter
MIGHT solve the problem.
P
P
h
h
o
o
n
n
e
e
C
C
o
o
n
n
n
n
e
e
c
c
t
t
i
i
o
o
n
n
The system's telephone line requirements are the
same as a standard telephone. Its connection to the
telephone line is the same as any NORMAL single
line telephone that you could buy at any department
store.
B
B
u
u
s
s
i
i
n
n
e
e
s
s
s
s
T
T
e
e
l
l
e
e
p
p
h
h
o
o
n
n
e
e
s
s
This system is not compatible with modular jacks
used for multi-line ELECTRONIC PHONE
SYSTEMS. To connect the SYSTEM to this type of
phone system, an RJ-11 jack must be ordered from
your local telephone company. It should be noted
that when the BA-1000 is used, the line indicator
lights on the phone system will not show the line as
being used.
S
S
i
i
n
n
g
g
l
l
e
e
L
L
i
i
n
n
e
e
P
P
h
h
o
o
n
n
e
e
s
s
If you have a single line phone it is probably
connected to a small modular jack. Simply unplug
the phone and plug the system in. If you wish to
have both the phone and the system connected at the
same time you can plug the phone into the PHONE
jack on the back of the BA-1000.
O
O
r
r
d
d
e
e
r
r
A
A
P
P
h
h
o
o
n
n
e
e
J
J
a
a
c
c
k
k
If you need to order a jack from the telephone
company, you will need the following information:
FCC No: AP494N-64812-MA-E
RINGER EQ.:0.0B
USOC No (Jack type) RJ-11, RJ-12, or RJ-13
(See telephone connection)
S
S
e
e
t
t
u
u
p
p
1. Connect the cord from the POWER CUBE to
the BA-1000.
2.
Plug the POWER CUBE to a power outlet. The
BA-1000
will
turn
on
automatically.
CAUTION: Do NOT disconnect the
POWER CUBE from the BA-1000 while it is
performing disk access functions. Doing so
will corrupt the data on the disk and will
require that you reformat the disk before
using it again.
3. Connect one end of the MODULAR CORD to
the BA-1000 and the other end to your RJ-11
telephone jack.
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
Each of these sections assumes you are starting from
the main MENU. You can always return to the
menu by pressing the ~
~
~
~ enough times.